Intermediate module of the communication system based on QwiicBus, which allows to extend the range of the I2C communication bus. The board use the NXP PCA9615 IC that converts two I2C signals into four differential signals, two for SCL and two for SDA. The differential signals are transmitted over an Ethernet cable, which is connected to the lead through the built-in RJ-45 connectors. Differential signaling enables I2C signals to reach distances up to 30 m. The module has a built-in converter that enables powering additional system components. Full documentation of the QwiicBus system with examples of use is available in the guide on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Kit for building a communication system based on QwiicBus. It contains two endpoint modules (EndPoint), an intermediary module (MidPoint) and two Ethernet cables. SparkFun KIT-17250
No product available!
End module of the communication system based on QwiicBus. It allows you to extend the range of the I2C bus. SparkFun COM-16988
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
Flexible 4-core cable, 100 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17259
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
The Qwiic connector overlay provides an easy-to-install way to add Qwiic connectors to Arduino Nano inserts. Communication takes place via the I2C interface. Sparkfun DEV-16789
Heart rate monitor module based on the popular MAX30101 chip. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-16474
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
GPS module with 72-channel GNSS NEO-M8U receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. Built-in accelerometer and gyroscope. SparkFun GPS-16329
Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842
Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476
Starter kit with Qwiic modules designed to work with the Raspberry Pi. The set consists of an overlay for Raspberry Pi with a standard 40-pin connector and four Qwiic connectors, OLED display, VCNL4040 distance sensor and environmental sensors. SparkFun KIT-16841
Data logger pre-programmed to automatically record data from IMU, GPS and Qwiic series sensors. SparkFun DEV-16832
Module with 20x4 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16398
No product available!
Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16397
No product available!
Module with 16x2 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16396
GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15712
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
Module with 24-bit ADC NAU7802 converter. It enables reading data from strain gauges and scales. I2C interface. SparkFun SEN-15242
GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15733
Module with a digital temperature and humidity sensor based on the SHTC3 system. Communication takes place via the I2C interface. SparkFun SEN-16467
Intermediate module of the communication system based on QwiicBus. It allows you to extend the range of the I2C bus. SparkFun COM-18000