

Module with 4-element segment display. Each of the four displays consists of 14 segments, so it can display not only numbers, such as the standard 7-segment display, but also letters and special characters. The display was connected to the VK16K33 controller operating with a voltage from 4.5 V to 5 V, so that when used with Arduino, a voltage level converter is not required. The user can configure the I2C address with two jumpers, which allows you to connect up to 4 such displays on one line. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V. Full documentation with examples of use is available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663
Board with the ATmega328 microcontroller from the AVR family, there are 20 I/O lines, 6 PWM channels, 6 analog inputs at the user\'s disposal. SparkFun DEV-15123
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
Flexible 4-core cable, 50 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17260
No product available!
LIDAR distance sensor with a measuring range from 5 cm to 10 m and a resolution of 1 cm. It communicates via the I2C or ANT interface. The set includes a module with Qwiic SparkFun SEN-18009 connectors
No product available!
Shield with Qwiic connectors designed for Raspberry Pi minicomputers. It allows you to easily connect the minicomputer with the Qwiic sensor system. SparkFun DEV-15945
Module with integrated proximity and ambient light sensors and IR emitter in the VCNL4040 system. It allows the detection of obstacles in the range of 0 to 20 cm (no dead zone). It communicates via the I2C bus. SparkFun SEN-15177
Module with ToF VL53L4CD sensor with a range of up to 1.3 m and a resolution of 1 mm. It is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun SEN-18993
Module with 512 kbit (64kB) EEPROM. Communication is via the I2C interface. The module has 3 jumpers to select one of 8 addresses. SparkFun COM-18355
Ultrasonic ToF (time-of-flight) rangefinder with a range of 4 cm to 1.2 meters. The sensor is able to simultaneously measure the range of several objects in its field of view. Communicates via I2C. SparkFun SPX-17271
No product available!
A 0.91-inch OLED display that offers a resolution of 128x32 pixels and the ability to display up to four lines of text. It communicates via an I2C interface and uses popular Qwiic connectors. SparkFun LCD-24606
Module with 3-axis accelerometer and ISM330DHCX gyroscope. Equipped with a Qwiic connector, it communicates via the I2C interface. SparkFun SEN-20176
No product available!
Air velocity sensor module based on the FS3000-1015 system. The board is equipped with connectors in the Qwiic standard. SparkFun SEN-18768
No product available!
Data logger pre-programmed to automatically record data from IMU, GPS and Qwiic series sensors. SparkFun DEV-16832
Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476
No product available!
Hub with Qwiic connectors that allows you to connect several boards to the evaluation kit. There is no built-in control system, but only splits one connector into 3 more. SparkFun BOB-18012
ToF distance sensor (Time of flight) with a range of up to 5 m. The module is supplied with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SEN-19036
Module with the MCP9600 amplifier designed to work with a K-type thermocouple. The module has a PCC connector for connecting this type of thermocouple. I2C communication. SparkFun SEN-16294
No product available!
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-18566