Module with 4-element segment display. Each of the four displays consists of 14 segments, so it can display not only numbers, such as the standard 7-segment display, but also letters and special characters. The display was connected to the VK16K33 controller operating with a voltage from 4.5 V to 5 V, so that when used with Arduino, a voltage level converter is not required. The user can configure the I2C address with two jumpers, which allows you to connect up to 4 such displays on one line. The module communicates via the I2C interface and is supplied with the voltage of 3.3 V. Full documentation with examples of use is available on the product page.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-15663
Board with the ATmega328 microcontroller from the AVR family, there are 20 I/O lines, 6 PWM channels, 6 analog inputs at the user\'s disposal. SparkFun DEV-15123
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
No product available!
Flexible 4-core cable, 500 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17257
Module with transparent OLED display. It has several display areas with different colors. I2C communication. SparkFun LCD-15079
No product available!
Module with integrated proximity and ambient light sensors and IR emitter in the VCNL4040 system. It allows the detection of obstacles in the range of 0 to 20 cm (no dead zone). It communicates via the I2C bus. SparkFun SEN-15177
Kit with RFID reader (125 kHz) equipped with I2C interface. Works with ID-3LA, ID-12LA and ID-20LA series systems (ID-12LA set). The RFID reader is simply plugged into the module\'s connectors. SparkFun KIT-15209
Module for RFID reader (125 kHz) equipped with I2C interface. Works with ID-3LA, ID-12LA and ID-20LA series systems. The selected RFID reader is simply plugged into the module\'s connectors. SparkFun SEN-15191
Module with three optical inspection sensors (spectrophotometers) from the AS7265x series. The module consists of three sensors; AS72651, AS72652 and AS72653 which can detect wavelengths from 410nm (UV) to 940nm (IR). SparkFun SEN-15050
No product available!
Module with a button and re LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-15932
The Qwiic connector overlay provides an easy-to-install way to add Qwiic connectors to Thing Plus and Feather boards. Communication takes place via the I2C interface. Sparkfun DEV-16790
The Qwiic connector overlay provides an easy-to-install way to add Qwiic connectors to Arduino Nano inserts. Communication takes place via the I2C interface. Sparkfun DEV-16789
Heart rate monitor module based on the popular MAX30101 chip. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-16474
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531
GPS module with 72-channel GNSS NEO-M8U receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. Built-in accelerometer and gyroscope. SparkFun GPS-16329
Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842
Miniature pressure measurement module equipped with a 25 psi piezoresistive pressure sensor. It allows you to perform calibrated and compensated pressure measurements from 60 mbar to 2.5 bar. SparkFun SEN-16476
Starter kit with Qwiic modules designed to work with the Raspberry Pi. The set consists of an overlay for Raspberry Pi with a standard 40-pin connector and four Qwiic connectors, OLED display, VCNL4040 distance sensor and environmental sensors. SparkFun KIT-16841
Data logger pre-programmed to automatically record data from IMU, GPS and Qwiic series sensors. SparkFun DEV-16832
Module with 20x4 characters LCD display and ATMega328p microcontroller. The user can communicate with the module through one of the serial interfaces: UART, I2C or SPI. SparkFun LCD-16398
No product available!
Module with a 4-element 14-segment display. The board is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun COM-18565