- Out-of-Stock

1.75 mm PLA filament for 3D printing by ROSA3D. 1 kg of filament is wound on the spool. The recommended printing temperature is in the range from 200°C to 230°C, and the bed temperature during printing in the range of 40°C - 60°C, however, when using adhesives, heating the bed is not necessary.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament. Filament PLA Starter from Rosa3D was designed for beginner users of 3D printers. The simplicity of PLA Starter printing will allow you to enjoy aesthetic prints, and over time will convince you to print more and more complex and demanding projects.
R-PLA is a recycled filament designed with the environment in mind. Like PLA, it is characterized by low shrinkage and no unpleasant odor. The prints are characterized by excellent layer adhesion and very good detail reproduction. The filament is made of a biodegradable polymer. It was made of ingredients approved for contact with food. The PLA Starter filament from Rosa3D was created with beginner users of 3D printers in mind. The simplicity of printing will allow you to enjoy aesthetic prints, and over time will convince you to print more and more complex and demanding projects.
R-PLA production batches may vary in color intensity ranging from dark gray, through graphite to anthracite black.
Knife designed for trimming and processing of prints from a 3D printer. It consists of a plastic handle and a replaceable, curved blade made of steel
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Spray 400ml
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Pen 90ml
3D printer with a filament sensor and colorful LED backlight. For self-assembly, included with the necessary accessories. BIQU B1
Teflon tube with a diameter of 8.9 mm. Works with 3D printers Flashforge Creator PRO and Flashforge Dreamer. Flashforge FF-TT-CP
No product available!
Cable with USB type A and lightning connectors, cable length 1m. LANBERG
No product available!
No product available!
No product available!
No product available!
A module with a spectrum sensor that operates in the visible light range (450-650 nm). It allows you to measure and characterize a light source or check how the tested surface absorbs or reflects light at specific wavelengths. Pimoroni PIM412
No product available!
AVT kit for self-assembly of the alarm control panel. AVT5466 B
No product available!
No product available!
AVT kit for self-assembly of an automatic charger for lead-acid batteries. AVT3120 B
No product available!
Male terminal block, angled, 3-pin. Pitch 5.0mm. Height 7.8mm. 2EDGRC-5.0-3P
No product available!
No product available!
Touchpanel for 128x64 M-series and CG-series displays, 67.5x47.8mm, ZIFF tape
No product available!
No product available!
No product available!
The P-NUCLEO-IOM01M1 is an STM32 Nucleo pack composed of the STEVAL-IOM001V1 and the NUCLEO-F446RE board. The STEVAL-IOM001V1 is a single IO-Link master PHY layer (L6360) while the NUCLEO- F446RE runs an IO-Link stack rev 1.1
No product available!
Module with 4 relays controlled by the I2C interface. Each relay can switch currents up to 40 A at 28-380 V AC. SparkFun KIT-16833
No product available!
ROSA3D filament made of high-quality, recycled PLA. 1 kg of 1.75 mm filament is wound on the spool. ROSA3D R-PLA Black