- Out-of-Stock
PureThermal 3 - module with the FLIR Lepton FS thermal imaging camera
ID: 1186200
5902186318755
A set with an adapter dedicated to the FLIR Lepton thermal imaging camera and the Lepton FS camera. It has been pre-configured to operate as a plug-and-play UVC 1.0 USB camera, it can also communicate via UART and I2C interface. SparkFun DEV-20813
Description
A set with an adapter dedicated to the FLIR Lepton thermal imaging camera and the FLIR Lepton FS camera. The adapter is pre-configured to function as a plug-and-play UVC 1.0 USB camera that will work with standard webcam drivers and video applications on all major platforms. PureThermal 3 is equipped with an STM32F412 microcontroller for image processing. The board also has pins with a raster of 2.54 mm, on which the UART and I2C interfaces were brought out.
The FLIR Lepton FS is a LWIR thermal imaging camera equipped with a matrix with a resolution of 160 x 120 pixels with progressive scan. It offers a viewing angle of 71° (diagonal) and 51° (horizontal) and can download data at a frequency of up to 8.7 Hz. It is calibrated and allows you to obtain accurate information about the temperature on the surface in a non-contact way. Thanks to its small size, the camera can be easily integrated with mobile devices as an infrared sensor. For communication, the module uses the SPI interface (image transfer) and I2C (configuration). The user has access to extensive support in the form of libraries and open-source GetThermal software.
Features
- Adapter compatible with all Lepton FLIR modules from the 2.x and 3.x series
- 9Hz color video over USB using UVC class USB
- STM32F412 ARM microcontroller
- Four mounting holes
- Compact housing ready to be built into production systems
- Firmware update (DFU) of STM32 ARM MCU via USB
- JTAG debugging via Tag-Connect EC10, ARM20-CTX, & ST-Link V/2
- UART and I2C interface
- Camera with a resolution of 160x120 pixels, FoV 71°/51° with a refresh rate of 8.7 Hz
- Power supply: VIN or USB type C
- Dimensions: 25.8 x 28.9mm
Kit contains
- PureThermal 3 Breakout Board
- FLiR Lepton FS Module
1186200
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Adapter dedicated to the FLIR Lepton thermal imaging camera. It has been pre-configured to act as a plug-and-play USB camera UVC 1.0, it can also communicate via UART and I2C interface. SparkFun DEV-14670
zł866.35
Delivery date unknown
No product available!
Lepton 3.5 thermal imaging camera module with PureThermal Mini Pro adapter. It allows you to connect the camera via the USB UVC interface, e.g. to a computer. SparkFun DEV-17544
zł2,271.60
24h
Available quantity: 1
Available
LWIR thermal imaging camera module equipped with a matrix with a resolution of 80x60 pixels with progressive scanning. It offers a viewing angle of 63.5° (diagonal) and 50° (horizontal) and can download data with a frequency of up to 8.6 Hz via the SPI interface. SparkFun SEN-16465
zł1,461.47
Delivery date unknown
No product available!
An adapter dedicated to the FLIR Lepton thermal imaging camera. It has been preconfigured to operate as a USB plug-and-play UVC 1.0 camera, and can also communicate via UART and I2C interfaces. SparkFun DEV-20812
zł864.58
Delivery date unknown
No product available!
Other products in the same category (16)
The Arduino M0 represents a simple, yet powerful, 32-bit extension of the Arduino UNO platform. The board is powered by Atmel’s SAMD21 MCU, featuring a 32-bit ARM Cortex® M0 core.
Retired
No product available!
Arduino Yun Mini is a breadboard PCB developed with ATmega 32u4 MCU and QCA MIPS 24K SoC CPU operating up to 400 MHz. Qualcomm Atheros CPU supports a Linux distribution based on OpenWRT named Linino. The board has built- in WiFi, supports 20 digital input/output pins, a 16 MHz crystal oscillator, a micro USB connector, an ICSP header, two reset buttons and one user button.
Retired
No product available!
The Arduino 4 Relays Shield allows your Arduino driving high power loads that cannot be controlled directly by Arduino\'s digital pins. The Shield features four relays, each relay with 2 pole changeover contacts (NO and NC). Four LEDs indicate the on/off state of each relay. (A000110)
Retired
No product available!
The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega
Retired
No product available!
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
Retired
No product available!
The Arduino 9 Axes Motion Shield allows your Arduino to measure movement: orientation, acceleration and magnetic field. A000070
Retired
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
Plastic holder that could fit all the boards with Arduino UNO size (68,6 mm x 53,4 mm). Contains 5 pieces in different colours. A000018
Delivery date unknown
No product available!
CryptoShield is a dedicated security peripheral for the Arduino. This shield adds specialized ICs that perform various cryptographic operations which will allow you to add a hardware security layer to your Arduino project. It also is a nice device for those performing embedded security research. DEV-13183
Retired
No product available!
No product available!
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
A set with an adapter dedicated to the FLIR Lepton thermal imaging camera and the Lepton FS camera. It has been pre-configured to operate as a plug-and-play UVC 1.0 USB camera, it can also communicate via UART and I2C interface. SparkFun DEV-20813