- Out-of-Stock
Cu (InGa) Se2 Based Thin Film Solar Cells
ID: 171609
Subba Kodigala
This book provides valuable content, particularly on the fabric of chalcopyrite based thin film solar cells. The characterization of solar cells, mainly absorbers (CuInGaSe2), buffers, window layers, antireflection coatings, finally metallic grids. When it's the problems of the solar cells, what are the problems of the XSS, XRD, AES, SEM, Raman, Photoluminescence, Electrical measurements etc. The absorber, which contains multiple elements always gives a segregation to the secondary phase. This kind of problems and details are given in the book. CuInGaSe2 thin film solar cell is illustrated with basic sciences. What are your criteria for solar cells, etc., are illustrated with several examples.
· Illustrates a number of growth techniques to prepare thin layers for solar cells
· Discusses characterization techniques such as XRD, TEM, XPS, AFM, SEM, PL, CL, Optical measurements, and Electrical measurements
· Includes IV, CV measurements illustrations
· Provides analysis of solar cell efficiency
Presents current trends in thin film solar cells research and marketing
Ch.1 Introduction
Ch.2 Growth Process of Cu (In 1-x Ga × ) Se 2 and CuIn (Se 1-x S x ) 2 Thin Films
Ch.3 Surface Analyzes of I-III-VI 2 Compounds
Ch.4 Structural Properties of I-III-VI 2 Absorbers
Ch.5 Optical Properties of I-III-VI 2 Compounds
Ch.6 Electrical Properties of I-III-VI 2 Compounds
Ch.7 Fabrication and Properties of Window Layers for Thin Film Solar Cells
Ch.8 CuIn 1-x Ga x Se 2 and CuIn (Se 1-x S x ) 2 Based Thin Film Solar Cells
· Illustrates a number of growth techniques to prepare thin layers for solar cells
· Discusses characterization techniques such as XRD, TEM, XPS, AFM, SEM, PL, CL, Optical measurements, and Electrical measurements
· Includes IV, CV measurements illustrations
· Provides analysis of solar cell efficiency
Presents current trends in thin film solar cells research and marketing
Ch.1 Introduction
Ch.2 Growth Process of Cu (In 1-x Ga × ) Se 2 and CuIn (Se 1-x S x ) 2 Thin Films
Ch.3 Surface Analyzes of I-III-VI 2 Compounds
Ch.4 Structural Properties of I-III-VI 2 Absorbers
Ch.5 Optical Properties of I-III-VI 2 Compounds
Ch.6 Electrical Properties of I-III-VI 2 Compounds
Ch.7 Fabrication and Properties of Window Layers for Thin Film Solar Cells
Ch.8 CuIn 1-x Ga x Se 2 and CuIn (Se 1-x S x ) 2 Based Thin Film Solar Cells
171609
Other products in the same category (16)
Based on Wi-Fi AP-Soc open source development board hardware
Retired
No product available!
The set consists of STM32 Nucleo NUCLEO-F302R8 plate with STM32F302R8 microcontroller, X-NUCLEO-IHM07M1 plate with BLDC L6230 three-phase motor controller and BR2804-1700kV engine
Retired
No product available!
3-Axis, Digital Magnetometer with I2C interface
Retired
No product available!
10 DOF IMU Sensor (B), Inertial Measurement Unit, Lower Power Consumption
Retired
No product available!
GSM/GPRS/GPS Shield, Phone Module, Arduino Shield Based on SIM908. Waveshare: GSM/GPRS/GPS Shield
Retired
No product available!
16 buttons controlled by only 1 AD port
Retired
No product available!
UART GPS Module, u-blox NEO-6M onboard, curved/horizontal pinheader
Retired
No product available!
No product available!
No product available!
A flux gel cartridge 10ml, necessary for assembly and repair of devices with surface-soldered components (SMT). The syringe makes it easier to apply the flux
Retired
No product available!
Miniature micro-SD card reader with USB 2.0 interface. The reader's casing is made of aluminum, pink. Works with both Windows and Mac OS
Retired
No product available!
Small and handy microSD card reader, enables reading cards on the computer (USB connector) as well as mobile devices (microUSB OTG connector)
Retired
No product available!
Breadboard-friendly development board with 32 bit ARM Cortex-M4. Adafruit 2756, DEV-13736
Retired
No product available!
The FXLN8361 three-axis accelerometer is a module with the FXLN8361 accelerometer system detecting the acceleration of an object during three-axis motion. The module can be supplied with voltage in the range of 3.3 ... 8V and provides two measuring ranges ± 2g and ± 8g. DFRobot SEN0178
Retired
No product available!
The MAXimator is an entry-level evaluation board with modern Altera MAX10 FPGA. The board can interface to external peripheral modules via Arduino Uno Rev 3 connectors. It also features HDMI+CEC+DCC and VGA interfaces
Retired
No product available!
The Kamami USB-Blaster is a programmer and configurator for PLD\'s manufactured by Altera. It is fully compatible with USB Blaster, then it can operate with a commercial and evaluation versions of the Altera Quartus project packet
Retired
No product available!
Subba Kodigala