- Out-of-Stock
AVT914 A +
ID: 190242
DIGITAL HUMIDITY METER - PLATE AND PROGRAMMED LAYOUT
DIGITAL HUMIDITY METER - PLATE AND PROGRAMMED LAYOUT
Producer: AVT
In the heating season, the problem of many apartments is too dry air - a factor causing unpleasant drying of the inhabitants' mucous membranes. Due to the relatively limited humidity range, at which residents feel good, it is worth to control it and maintain it at an appropriate level. Therefore, a moisture meter is necessary.
The AVT914 kit uses a RHU1015 module as a humidity sensor. It provides voltage proportional to humidity. The signal is then converted into an A / C converter and the result is shown on the LCD display.
The device is especially recommended as home furnishings and everyone who likes to control climate change
Selected parameters of the hygrometer:
- relative humidity RH
- measuring range 10-90% RH
- time of determination of results <5 min
- working temperature 0-40 ° C
- measurement error <+/- 5%
- built-in temperature compensation system
- presenting results - LCD display
- power supply - 9-15 V
- a printed circuit board, programmed layout and documentation in the set
Detailed description in EP 1/06
Download
190242
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
No product available!
12 pin GPIO ribbon cable (200mm) for Odroid XU4 and Odroid XU4Q
Retired
No product available!
7 pin GPIO ribbon cable (20 cm) for Odroid C4
Retired
No product available!
No product available!
3-wire cable with JST-ZH plug, 30 cm, 3x1 JST, 1.5 mm pitch
Retired
No product available!
A set for building a four-wheel, remote-controlled vehicle. Equipped with a programmable Arduino Uno R3 controller and set of sensors. modARD_02
Retired
No product available!
No product available!
No product available!
800x480, 7 inch Multicolor Graphic LCD, with capacitive touch screen and stand-alone touch controller
Retired
No product available!
An intelligent socket with the ability to control via Wi-Fi. It allows remote switching on / off of the device powered from 230V mains with a maximum power consumption of 10 A. The device works with the eWeLnik smartphone application
Retired
No product available!
Switch (relay) controlled via GSM / GPRS network. The switch (relay) allows remote control of the device powered from 230 V mains with a maximum power consumption of 16 A. The device works with the eWeLnik smartphone application
Delivery date unknown
No product available!
No product available!
The Google AIY Voice Kit is a set of components designed for the Rasbperry Pi 3 computer, allowing you to build an intelligent voice assistant based on Google Assistant. The kit can also work with TensorFlow. The kit requires self-assembly. Adafruit 3602
Retired
No product available!
This fully-featured UDA1334A I2S Stereo DAC breakout is a perfect match for any I2S-output audio interface. It\'s affordable but sounds great! The NXP UDA1334A is a jack-of-all-I2S-trades: you can use 3.3V - 5V logic levels (a rarity), and can process multiple different formats by setting two pins to high or low. Adafruit 3678
Retired
No product available!
PCB with a programmed layout for an animated 3D LED bomb controlled by an IR remote control. AVT1986 A +
Retired
No product available!
AVT kit for self-assembly of animated 3D LED baubles controlled by IR remote control. AVT1986 B
Retired
No product available!
DIGITAL HUMIDITY METER - PLATE AND PROGRAMMED LAYOUT