- Out-of-Stock
AVT988 C
ID: 193042
AVRISP PROGRAMMER - SET ASSEMBLED AND STARTED
AVRISP PROGRAMMER - SET ASSEMBLED AND STARTED
Producer: AVT
The AVR Studio environment offers the possibility of operating mainly "company" programmers; such as STK500 or AVRISP. Nothing, however, stands in the way of making a "pretend" layout under one of the company's designs. This is not a particularly difficult task, especially since Atmel has provided a communication protocol between the PC and the programmer, as well as a description of the signals necessary for correct programming of the processor.
The programmer consists of three main blocks: the FT232RL system which is the computer's USB port interface, the ATmega 8 microcontroller realizing all logic functions and the output buffer. The whole is powered directly from the USB interface line.
The device is especially recommended for electronics using AVR microcontrollers and the AVR Studio 4.12 programming environment
Selected parameters:
- compliance with the STK500V2 protocol
- direct support via AVR Studio 4
- computer interface - USB
- support for USB bus sleep mode
- programming processors in the system via the Atmel standard connector
- programming of un-mounted processors (with the use of stands)
- programming in systems with supply voltages in the range of 2.7-5V (below 2V without a guarantee)
- high programming speed
- power supply - from the USB port
- tile dimensions 60x41mm
- system assembled and running + wiring
Detailed description in EP 7/07
Download
193042
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Video splitter for connecting one input device to 4 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0004
Retired
No product available!
Video splitter for connecting one input device to 8 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0008
Retired
No product available!
Video switch that allows you to connect 5 input devices to one HDMI receiver. The input signal can be selected using a button on the casing or the included remote control. Lanberg SWV-HDMI-0005
Retired
No product available!
A set of 8 knives, including 4 knives with broken blades and 4 special-purpose knives. Vorel 76280
Retired
No product available!
Module with an analog temperature and humidity sensor based on the SHT10 system. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers. DFRobot DFR0066
Retired
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318
Retired
No product available!
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
Retired
No product available!
Module with a 3-axis analog MMA7361 accelerometer. There are 3 Gravity connectors on the board (for each axis). The operating range of the sensor can be configured using a DIP switch. DFRobot DFR0143
Retired
No product available!
Module with a UV ultraviolet light sensor VEML6075. Enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. DFRobot SEN0303
Retired
No product available!
The I2C-GPIO converter module is powered with the voltage of 5 V. It allows you to extend the number of digital pins of the Arduino-compatible board with an additional 16 IO pins. DFRobot DFR0013
Retired
No product available!
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
Retired
No product available!
Opening/closing sensor designed for mounting on windows and doors. It is equipped with an RF wireless communication module operating at 433 MHz. Sonoff DW2 - RF
Retired
No product available!
Opening/closing sensor designed for mounting on windows and doors. It is equipped with a WiFi wireless communication module. Sonoff DW2
Retired
No product available!
Universal WiFi controlled switch. It can control one home appliance. Sonoff Basic R2 v2.2
Retired
No product available!
Wireless temperature and humidity sensor. It allows you to track changes in temperature and humidity in your home. Shelly H&T
Retired
No product available!
Power adapter with a microUSB socket designed for the Shelly H&T sensor. It allows you to replace the battery power of the sensor with a constant 5V power supply. Shelly H&T Usb Adapter
Retired
No product available!
AVRISP PROGRAMMER - SET ASSEMBLED AND STARTED