- Out-of-Stock
Gravity: CCS811 Air Quality Sensor - module with air quality sensor
ID: 581629
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318
Description
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (CO2) and volatile organic compounds (VOC) in the air. It communicates via the I2C interface (Gravity connector). Integrated ADC and MCU enable data collection and processing. The sensor has the ability to generate an alarm when the level set by the user is exceeded. It can be widely used in many areas such as air quality detection, air purifiers and ventilation systems. The user manual and sample programs can be found on the product Wiki page.
Features
- Time to first measurement: <15 s
- Communication: I2C
- I2C address: 0x5A (default) / 0x5B
- ECO2 measuring range: 400ppm to 8000ppm
- TVOC measurement range: 0ppb to 1100ppb
- Voltage: 3.3 V to 5.5 V
- Operating temperature range: -40 ℃ to 85 ℃
- Operating humidity range: 10% RH to 95% RH
- Dimensions: 22 x 31 mm
Kit contains
- Module with CCS811 sensor
- Gravity cable
- 2 x Straight 4-pin goldpin
581629
Data sheet
- Interface
- I2C
- Type of sensor
- CCS811
- Power supply voltage
- 3,3 - 5 V
- Concentration measurement
- VOC/CO2
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 205
Available
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.41
24h
Available quantity: 4
Available
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
zł27.58
24h
Available quantity: 6
Available
Other products in the same category (16)
This compact, inexpensive plastic gearmotor (high-power brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Retired
No product available!
Digital Proximity, Ambient Light, RGB and Gesture Sensor, Avago Technologies, RoHS
Retired
No product available!
Integrated analogue base station RFID (front-end) of the company EM Microelectronic with a frequency of 13.56MHz. The system has a SOP20 housing
Retired
No product available!
Computer fan housing Raspberry Pi 3, Raspberry Pi 2 model B and Raspberry Pi 1 model B + in dark blue plastic color
Retired
No product available!
Case for the Raspberry PI 2 model B, Raspberry PI 1 model B+ and Raspberry PI 3 computers, manufactured from high quality acrylic. CLEAR
Retired
No product available!
No product available!
No product available!
No product available!
Infrared sensor that allows measurement of distances up to 15cm, has a built-in infrared illuminator, IR receiver and a perimeter of the received signal
Retired
No product available!
Miniature (22x13.5x6mm) WiFi module b / g / n with TCP and UDP protocols operating in standalone and access point modes. 2.0mm goldpin connector. The module is equipped with a UART interface, it is also possible to control GPIO lines (also as PWM). Powered by 3.3V. Antenna: copper wire
Retired
No product available!
Ultra miniature WiFi b/g/n module, equipped with UART, SPI, PWM and GPIO interfaces. The ability to work as an access point and in standalone mode. 3.3V power supply.HF-LPT200-1
Retired
No product available!
This transducer is about 45mm in diameter and has 4Ω impedance and should be run at about 5W
Retired
No product available!
SPIRIT1 868 MHz low power RF module with integrated microcontroller
Delivery date unknown
No product available!
Read/Write analog front end for 125 kHz RFID Basestation, SOIC16, EM Microrlectronic, RoHS
Retired
No product available!
Bitscope Micro is a miniature measuring instrument with a USB interface, it can act as an 8-channel logic analyzer (40MS / s, 3.3V or 5V) or a 2-channel oscilloscope (bandwidth up to 20MHz). In addition, Bitscope can generate a clock signal as well as sinusoidal, triangular, rectangular and saws
Retired
No product available!
High performance WLAN USB module which enables the Raspberry Pi to connect to a Wi-Fi network
Retired
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318