- Out-of-Stock
Gravity: Gesture & Touch Sensor - module with a gesture and touch sensor
ID: 581647
5906623406609
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
Description
Module with a gesture and touch sensor. It allows you to recognize 7 types of gestures: left, right, forward, backward, up, down, swipe and remove your hand. There are 5 touch buttons on the board that can be used directly on the module or extended with wires. The module is supplied with voltage ranging from 3.3 V to 5 V and communicates via the UART interface. On the Wiki page there is a user manual and sample programs.
Features
- Gesture detection range: 30 cm
- Supported gestures: move left, right, forward, backward, up, down, swipe and remove hand
- 5 touch buttons
- Communication: UART (9600 8n1)
- Working voltage: 3.3V to 5V
- Current consumption: 56.3 mA (in sleep mode: 40uA)
- Dimensions: 36 x 32 mm
Kit contains
- Module with a gesture and touch sensor
- 4-pin Gravity cable
581647
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.57
24h
Available quantity: 226
Available
No product available!
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł21.66
Delivery date unknown
No product available!
Board with ATmega1280 microcontroller from the AVR family, the user has 54 I/O lines, 14 PWM channels, 16 analog inputs. DFRobot DFR0003
zł89.20
Delivery date unknown
No product available!
Other products in the same category (16)
The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. WRL-10421
Retired
No product available!
No product available!
Adafruit 960 - GPS Antenna - External Active Antenna - 3-5V 28dB 5 Meter SMA
Retired
No product available!
Adafruit 948 - EL Flowing Effect Wire with Inverter - Blue 2.0 meter (6.5 ft)
Retired
No product available!
Adafruit 942 - Adafruit Pi Dish for Raspberry Pi - Includes Breadboard
Retired
No product available!
Adafruit 856 - MCP3008 - 8-Channel 10-Bit ADC With SPI Interface
Retired
No product available!
Adafruit 851 - SMA to uFL/u.FL/IPX/IPEX RF Adapter Cable
Retired
No product available!
Adafruit 833 - Liquid Flow Meter - Brass 1/2" Nominal Threaded
Retired
No product available!
Adafruit 804 - PS/2 Wired Connector - Panel Mount MiniDIN-6
Retired
No product available!
Adafruit 800 - Netduino Go! Starter Pack (Modular .NET microcontroller)
Retired
No product available!
Adafruit 72 - DC Boarduino (Arduino compatible) Kit (w/ATmega328) - v1.0
Retired
No product available!
Adafruit 714 - RGB LCD Shield Kit w/ 16x2 Character Display - Only 2 pins used! - NEGATIVE DISPLAY
Retired
No product available!
Adafruit 659 - FLORA - Wearable electronic platform: Arduino-compatible - v2
Retired
No product available!
No product available!
No product available!
TSL2561 luminosity sensor is an advanced digital light sensor, ideal for use in a wide range of light situations. Compared to low cost CdS cells, this sensor is more precise, allowing for exact lux calculations and can be configured for different gain/timing ranges to detect light ranges from up to 0.1 - 40,000+ Lux on the fly. Adafruit 439
Retired
No product available!
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285