.png)
- Out-of-Stock
Pololu 1483 - Carbon Monoxide Flammable Gas Sensor MQ-9
ID: 196149
Carbon Monoxide & Flammable Gas Sensor MQ-9
Carbon Monoxide & Flammable Gas Sensor MQ-9
This semiconductor gas sensor detects the presence of Carbon Monoxide at concentrations from 10 to 1,000 ppm and combustible gas from 100 to 10,000 ppm. The sensor’s simple analog voltage interface requires only one analog input pin from your microcontroller.
 |
Overview
This Carbon Monoxide (CO) and flammable gas sensor detects the concentrations of CO and combustible gas in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of CO from 10 to 1,000 ppm and flammable gas from 100 to 10,000 ppm.The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V. Please read the MQ9 datasheet (180k pdf) for more information about the sensor.
 |
| Gas sensor with orange plastic case bottom view. |
|---|
Connections
Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 20 kΩ.
We offer two breakout boards that make it easier to interface with these sensors: a Pololu carrier board and a SparkFun carrier board. The Pololu version is shown below.
|
People often buy this product together with:
 |
Pololu MQ Gas Sensor Carrier |
 |
Flammable Gas & Smoke Sensor MQ-2 |
|
Methane Gas Sensor MQ-4 |
196149
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Other products in the same category (16)
Starter Cable Kit for Spacely Carrier. Connect Tech CKG045
Retired
No product available!
Base board for NVIDIA Jetson TX1, NVIDIA Jetson TX2 or NVIDIA Jetson TX2i modules. It is equipped with MIPI CSI-2 connector, USB OTG, UART and I2C. It is characterized by great possibilities with small tile dimensions. Connect Tech ASG008
Retired
No product available!
Starter Cable Kit for Astro Breakout Board. Connect Tech CKG041
Retired
No product available!
Base board for NVIDIA Jetson TX1, NVIDIA Jetson TX2 or NVIDIA Jetson TX2i modules. The board is equipped with a Mini PCI Express and mSATA connector, as well as a micro SD card slot. It is characterized by great possibilities with small tile dimensions. Connect Tech ASG001
Retired
No product available!
A network card that supports two WiFi frequency bands (2.4GHz and 5GHz) with a USB connector. It allows you to connect devices without an internal network adapter to the WiFi network. TP-LINK AC600
Retired
No product available!
Integrated capacitive fingerprint sensor communicating with the external system via the UART interface. The module has a rectangular sensor field and downloads a fingerprint image with a resolution of 508dpi. Waveshare UART Fingerprint Sensor (R)
Retired
No product available!
Sipeed MAIX Bit is a RISC-V 64 development board for AI + IoT applications. Seeed Studio 110991190
Retired
No product available!
Based on MAIX Module, the Maixduino is a RISC-V 64 development board for AI + IoT applications. Seeed Studio 110110044
Retired
No product available!
Module with 12.48" e-Paper display and 1304x984 px resolution. Communicates with external systems via the SPI interface. It has low power consumption and a wide viewing angle. Waveshare 12.48inch e-paper Module
Retired
No product available!
RoboClaw 2x60AHV Motor Controller (V7C) is a two-channel DC motor driver, operating voltage: 10,5 to 60V, maximum continuous current: 60A, the ability to easily implement feedback loops with PID controller, security systems. Pololu 3583
Retired
No product available!
Gate driver in uWiFi technology with extended range, with application for Android/iOS. BleBox GateBoxPro
Retired
No product available!
Camera module with MT9J003 sensor cooperating with ArduCam USB Shield. The maximum video resolution is 3856x2764 pixels. LS-18023 lens mount possible. ArduCam A0096
Retired
No product available!
A 150mm 2-wire cable terminated terminated with a plug and socket JST XH2.54.. 22AWG cable diameter.
Retired
No product available!
Digital microscope with 3" LCD display and HDMI output. The microscope is equipped with a 3MPx image sensor with a magnification factor up to 300 times. Andonstar ADSM201
Retired
No product available!
120W power supply, 24VDC output voltage and 5A output current. Mounting on a DIN rail. Built-in overload and short circuit protection. MEAN WELL DR-120-24
Retired
No product available!
A hand-held thermal imaging camera with a 2.4" LCD screen. It measures the temperature in the range from -20 to 300°C. HTI HT-02D
Retired
No product available!
Carbon Monoxide & Flammable Gas Sensor MQ-9