- Out-of-Stock
AVT1527 B
ID: 193057
PSoC PROGRAMMER - A SELF-ASSEMBLY KIT
PSoC PROGRAMMER - A SELF-ASSEMBLY KIT
Producer: AVT
In order to meet the expectations of many electronic engineers, we present a project of an inexpensive PSoC programmer for microcontrollers programmed using the ISSP interface that allows entering and changing software in the system. Thanks to this, it is not necessary to buy a large stationary programmer, this way of operation also facilitates the launch of the target system.
The presented programmer has a very simple structure; it consists of virtually a few very cheap elements. It works with the dedicated Cyp software and supports programming of the PSoC microcontrollers in two modes: PowerOn and Reset.
The device is especially recommended on the website and all electronics constructing complaints based on PSoC processors
Selected parameters:
- for programming PSoC processors
- two PowerOn and Reset modes available
- free Cyp software
- operation status indication - LED
- small dimensions, very small number of elements
- power supply - from the programmed system
- in the set a printed circuit board, a set of elements and documentation
- Detailed description in
Download
193057
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Pre-installed Android4.4 or latest version for ODROID-XU3 and XU4. Ready to run out of box 8Gbyte eMMC Version 5.0 interface from Toshiba. JEDEC/MMCA version 5.0:HS400 interface with 8bit DDR mode
Retired
No product available!
Pre-installed XUbuntu 15.04 or latest version for ODROID-XU3, XU4 and HC1
Retired
No product available!
Pre-installed XUbuntu 15.04 or latest version for ODROID-XU3, XU4 and HC1
Retired
No product available!
The Cloudshell for XU4 is an affordable DIY Network Attached Storage (NAS) Solution to create your own personal cloud! It includes a color LCD console display on the front and has room for a 2.5inch HDD/SSD along with the XU4 board inside the CloudShell
Retired
No product available!
The Cloudshell for XU4 is an affordable DIY Network Attached Storage (NAS) Solution to create your own personal cloud! It includes a color LCD console display on the front and has room for a 2.5inch HDD/SSD along with the XU4 board inside the CloudShell
Retired
No product available!
Cooling Fan X is a cooling fan that can be used to cool any processor that works under heavy load. It can be mounted on the heat sink housing with 4 screws
Retired
No product available!
Photon Wearable Shield makes it easy to add the WiFi enabled Photon to any wearables project. Each pin on the Photon is broken out into large sewing pins. Use conductive thread to make your next wearables projects. DEV-13328
Retired
No product available!
The cable allows connecting the ATMEL-ICE programmer to the commissioning set with any connector (operated by the programmer), through individual pin connectors
Retired
No product available!
1-channel monochrome system of adding subtitles on the image (OSD - On-Screen Display) with integrated EEPROM, TSSOP28, Maxim memory
Retired
No product available!
No product available!
The controller can control two brush motors, communicating with the master system using USB Micro-B, TTL serial interface, analog signals, as well as signals from the RC apparatus. The current capacity of 5A / channel allows you to control high-power motors. Polol 2394
Retired
No product available!
EEPROM CAT93C86LI-G memory; 16kbit; 2K x 8bit; access time: 150ns; Power supply: 1.8 ... 5.5 V; 8-Pin PDIP
Retired
No product available!
Nettemp Pi Hat is a module that allows to connect eight trees of sensors with I2C/1-Wire interface and control of four relays outputs. Thanks to the extension board is possible to build in an easy way e.g. a multipunkt temperature controller.
Retired
No product available!
32GB microSDHC Memory Card with SD Adapter, class 10 A1, Kingston
Retired
No product available!
WiFi 802.11 b / g / n module with ESP8266 system, 5 leads are available with 2 mm pitch with the possibility of soldering of gold pins, power lines, reset line and UART interface have been led to the connector. 3.3V power supply
Retired
No product available!
WiFi 802.11 b / g / n module with ESP8266 system, 8 pins with 2.54 mm pitch are available with soldered gold pins, 3 GPIO lines, reset, power supply and UART interface on the connector. U.FL. Antenna Connector 3.3 V power supply
Retired
No product available!
PSoC PROGRAMMER - A SELF-ASSEMBLY KIT