- Out-of-Stock
AVT5119 A +
ID: 193823
KEELOG CONTROLLER - PLATE INCLUDED AND PROGRAMMED
KEELOG CONTROLLER - PLATE INCLUDED AND PROGRAMMED
Producer: AVT
The set enables wireless control of two relays. Radio waves were used as the signal carrier. This solution was chosen due to the wider application possibilities - the operation of the device is not limited to one room (as in the case of infrared signals). An additional assumption is the use of ready-made pilots, in order to avoid any difficulties associated with tuning the radio track. The transmitters operating in the widespread Keeloq coding system used in car alarm systems were selected.
The device is especially recommended where it is necessary to remotely switch on and turn off electrical devices
Selected parameters:
- number of independent channels - 2
- range> 20m
- number of pilots that can be used - 8
- operating frequency 433MHz
- command coding (Keeloq)
- executive elements - relays
- contact load 8A / 250V
- power supply - 12 Vdc (receiver)
- tile dimensions 104x41mm
- a printed circuit board, programmed layout and documentation in the set
Detailed description in EP 12/07
Download
193823
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
No product available!
The 5V/2A wireless charging module is an advanced solution for contactless power transfer, utilizing magnetic-coupled resonance technology. It ensures high energy transfer efficiency (up to 90%) with minimal power consumption. The module\'s ability to be fully sealed makes it waterproof and dustproof, extending its lifespan and increasing usability. It is perfect for powering phones, portable devices, and DIY projects. DFRobot DFR0712
Retired
No product available!
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Glitter Graphite
Retired
No product available!
Dov M. Gabbay, Dimitrij Skvortsov, Valentin Shehtman
Delivery date unknown
No product available!
MYIR MYC-C7Z020 is a single board computer module based on the MYC-C7Z020 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.
Retired
No product available!
No product available!
No product available!
No product available!
Assembled module of comfortable direction indicators. AVT1945 C
Retired
No product available!
No product available!
No product available!
DSLR SHUTTER ELECTRONIC DRAIN HOSE FOR A PHOTOGRAPHIC APPARATUS - A KIT FOR SELF-ASSEMBLY
Retired
No product available!
Motion MEMS and environmental sensor expansion board for STM32 Nucleo, equipped with Arduino UNO R3 connector layout; designed around the LSM6DSL 3D accelerometer and 3D gyroscope, the LSM303AGR 3D accelerometer and 3D magnetometer, the HTS221 humidity and temperature sensor and the LPS22HB pressure sensor. The board interfaces with the STM32 microcontroller via the I²C pin
Retired
No product available!
ELF-VLF MULTIODORNIK ELEMENT - RECEIVER COOPERATING WITH MAGNETIC ANTENNA AND- PRINTED PLATE
Retired
No product available!
No product available!
KEELOG CONTROLLER - PLATE INCLUDED AND PROGRAMMED