- Out-of-Stock
zł971.80
AVT913 A
ID: 193973
UNIVERSAL LOADER NI-MH AND NICD - PRINTED PLATE
UNIVERSAL LOADER NI-MH AND NICD - PRINTED PLATE
Producer: AVT
The charger uses a modern, specialized integrated circuit type LM 3647. It is equipped with a signaling block consisting of three LEDs and a buzzer, an interface that allows you to configure the charger's work mode, current measurement circuits, voltage and temperature of cells and a controller of executive systems. Depending on the configuration method, the battery charging process is based on various algorithms.
The charger can be used for NiCd and NiMH batteries and after a small modification - LiIon.
The device is especially recommended for users of various types of batteries, modelers, photographers, etc.
Selected charger parameters:
- possibility of cooperation with NiCd, NiMH and LiIon batteries
- number of simultaneously charged cells: 2-10
- operating modes: without pre-discharge, with pre-discharge, maintenance
- status signaling - LED diodes
- acoustic signal output
- power supply - 12-20 Vdc
- printed circuit board and documentation included
- Detailed description in
Download
193973
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Expansion card dedicated for sets from the Terasic DE FPGA series. It contains mainly elements necessary for communication (Wi-Fi module and Bluetooth) and sensors (light, humidity, temperature, accelerometer, gyroscope and magnetometer). The built-in UART <> USB converter enables communication with a PC. Terasic P0499
Retired
No product available!
Module with a light sensor based on the APDS-9002 system. With the aid of this system, it is possible to measure the intensity of illumination in lux. The module has a connector in accordance with the Grove standard. Seeed studio 101020076
Retired
No product available!
Module with SSR S208T02 relay with a load up to 4 A. The board is equipped with a Grove connector and is controlled by a digital input. Seeed Studio 103020004
Retired
No product available!
Module with a reed relay BR-500Ω with a load up to 0.5 A. The board is equipped with a Grove connector and is controlled by a digital input. Seeed Studio 103020014
Retired
No product available!
Module with a 3-axis gyroscope (ITG 3200 system). The measuring range is ± 2000 ° / s. The I2C interface is used for communication. The module has a low power consumption (typically 6.5 mA). The module has a connector in accordance with the Grove standard. Seeed studio 101020050
Retired
No product available!
Module module with ADC121C021 12-bit converter. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 103020013
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
Twisted housing, dedicated to the Orange Pi Zero computer. The housing protects the computer against dust, accidental short circuits and mechanical damage. Properly prepared holes allow you to use all the sockets that Orange Pi Zero has been equipped with.
Retired
No product available!
No product available!
Banana Pi M2+ is another ARM SoC powered development board that offers great computing performance in an ultra portable form factor. It is a 65mm square with Allwinner H3 Quad-core A7 SoC and 1GB DDR3 RAM
Retired
No product available!
Banana Pi camera module for Banana Pi M3, includes CMOS sensor module: OV5640 (5M Pixel)
Retired
No product available!
Printed circuit board and programmed AA / AAA cell capacity tester. AVT3169 A +
Retired
No product available!
AVT kit for self-assembly of tester capacity AA / AAA cells. AVT3169 B
Retired
No product available!
UNIVERSAL LOADER NI-MH AND NICD - PRINTED PLATE