- Out-of-Stock
ST VNH2SP30 30A Motor Driver
The VNH2SP30 is an improved version of the VNH3SP30 motor driver, featuring current sensing, increased drive capability, and a higher maximum PWM frequency of 20 kHz.
We use these motor drivers in several of our products, including the single and dual motor driver carrier boards, the jrk 12v12 motor controller w/feedback, the TReX motor controller, the qik 2s12v10, and the Orangutan X2 robot controller. We offer the chips by themselves for more direct integration into your project or product.
| VNH3SP30 | VNH2SP30 | |
|---|---|---|
| Operating supply voltage (Vcc) | 5.5 – 36 V* | 5.5 – 16 V |
| Maximum current rating | 30 A | 30 A |
| MOSFET on-resistance (per leg) | 34 mΩ | 19 mΩ |
| Maximum PWM frequency | 10 kHz | 20 kHz |
| Current sense | none | approximately 0.13 V/A |
| Over-voltage shutoff | 36 V* | 16 V minimum (19 V typical) |
| Time to overheat at 20 A** | 8 seconds | 35 seconds |
| Time to overheat at 15 A** | 30 seconds | 150 seconds |
| Current for infinite run time** | 9 A | 14 A |
*Manufacturer specification. In our experience, shoot-through currents make PWM operation impractical above 16 V.
**Typical results using Pololu motor driver carrier with 100% duty cycle at room temperature.
The motor drivers have maximum current ratings of 30 A continuous. However, the chips by themselves will overheat at lower currents (see table above for an example set of values). The actual current you can deliver will depend on how well you can keep the motor driver cool. Good air flow and a heat sink will allow the chip to operate at currents closer to its maximum rating without overheating.
Many motor controllers or speed controllers can have peak current ratings that are substantially higher than the continuous current rating; this is not the case with these motor drivers, which have a 30 A continuous rating and a over-current protection that can kick in as low as 30 A (45 A typical). Therefore, the stall current of your motor should not be more than 30 A. (Even if you expect to run at a much lower average current, the motor can still draw high currents when it is starting or if you use low duty cycle PWM to keep the average current down.)
Note: This motor driver IC comes in a MultiPowerSO-30 package that requires surface mounting; it is not a through-hole component. Our carrier boards give you convenient access to the VNH2SP30 and VNH3SP30 motor drivers without any surface-mount soldering.
Manufacturer
Responsible person
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Blue Satin
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Grey
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Green
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Red
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Winter White
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Yellow
No product available!
A kit for building an autonomous racing robot based on the NVIDIA Jetson Nano B01 development kit. Waveshare JetRacer ROS AI Kit A
No product available!
A kit for building an autonomous crawler robot based on the NVIDIA Jetson Nano B01. Waveshare JETANK AI Kit A
No product available!
DC motor with 1:48 plastic gearbox and double-sided shaft. Equipped with incremental encoder with Hall sensors. Includes bracket, mounting hardware and cord
No product available!
USB 2.0 port isolator with support for Low Speed and Full Speed. The device has an isolation voltage rating of 3000 V. The isolator can be powered from the USB port, it is possible to connect an external power supply. USB-4620
No product available!
USB port isolator used for galvanic isolation of USB connection. It uses ADI (Analog Devices iCoupler) technology. EVC9001
No product available!
Female terminal block, 2-pin. Pitch 3.81mm. Height 7.8mm. Suitable for 15EDGRC male strips with a pitch of 3.81 mm. 2EDGKN-3.81
No product available!
Male terminal block, angled, 2-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
No product available!
Male terminal block, angled, 3-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
No product available!
Male terminal block, angled, 4-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
No product available!
Male terminal block, angled, 5-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
No product available!
ST VNH2SP30 30A Motor Driver