- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
Hobbyking 2~6S Lipo to USB Charging Adapter and Cell Checker
ID: 222599
HK Hobbyking 2~6S Lipo to USB Charging Adapter and Cell Checker (22320)
Hobbyking 2~6S Lipo to USB Charging Adapter and Cell Checker (22320)
This handy little device allows you to charge your mobile phone, USB keychain camera or any other 5V USB device at the field with a 2~6S Lipoly battery. It uses the balance plug (JST-XH) from your Lipoly battery for power. This device also doubles as a cell voltage checker thanks to the on-board LCD display. Low-voltage input protection will shut this device down should the input source voltage drop below 3V. This prevents critical over-discharging of your input battery.
Features:
• Compact size
• 2~6S Lipoly input
• 5V/1000mAh USB output
• Convenient field charging of your mobile device
Specs:
USB Output: 5V/1000mAh
Input Voltage: DC 7.5~25.2V
Cell Checking: 1~6S Lipoly
Input Cut-Off Voltage: 3V per cell
PRODUCT ID: 9070000027
222599
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Other products in the same category (16)
A needle with a diameter of 0.4 mm, designed for cleaning the nozzle in 3D printers. It allows you to get rid of the remnants of the material after printing and to remove the filament in case of clogged nozzle
Retired
No product available!
Connector for connecting the 22-pin tape with 0.5 mm pitch to the printed circuit board. F0500WR-S-22PB
Retired
No product available!
Aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has four wires. It is used in kitchen scales and portable scales
Retired
No product available!
Educational set for building robots based on Totem construction elements. Designed for beginners, it allows you to create 7 robot structures based on the included assembly instructions. Totem TKR-RK1
Retired
No product available!
A computer adapter (USB, Ethernet, WiFi) that works as a 4-channel oscilloscope, a 16-channel logic analyzer and a programmable signal generator. Includes BNC probes. Digilent 471-040
Retired
No product available!
A computer adapter (USB, Ethernet, WiFi) that works as a 2-channel oscilloscope, a 16-channel logic analyzer and a programmable signal generator. Includes BNC oscilloscope probes. Digilent 471-041
Retired
No product available!
Transistor tester dedicated to work with Analog Discovery 2 and Analog Discovery (Legacy) devices. It allows you to draw the characteristics of such elements as diodes, NPN and PNP transistors as well as P and N FET transistors. Digilent 410-413
Retired
No product available!
Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM331
Retired
No product available!
Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM332
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin output for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM320
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM321
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM322
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and two sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM511
Retired
No product available!
Extension module for Raspberry Pi. The board has 7 RGB LEDs, four 14-segment displays, three single-color LEDs, as well as three touch buttons, a BMP280 sensor and a buzzer. Pimoroni PIM242
Retired
No product available!
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
Module with 6 5x7 LED matrix displays designed to work with the Raspberry Pi. It uses IS31FL3730 drivers and communicates via the I2C interface. Pimoroni PIM187
Retired
No product available!
HK Hobbyking 2~6S Lipo to USB Charging Adapter and Cell Checker (22320)