- Out-of-Stock
200:1 6V - plastic gear motor (90° Output)
ID: 195506
Plastic gear motor 200:1, output shaft at 90°, operating voltage 6 V, current consumption from 0.07 A to 0.8 A, speed 51 RPM and a maximum torque of 7.2 kg*cm. Pololu 1120
Description
Motor with plastic gear 200:1 and output shaft at a 90° angle with flattened sides with a diameter of 7 mm and a length of approx. 6 mm. The recommended operating voltage of the motor is 6 V and at this voltage it achieves a speed of 51 RPM and a maximum torque of 7.2 kg*cm, consuming a current from 0.07 A to 0.8 A.
Suitable mounting brackets in the standard and high version are available for the motors.
Our offer includes a number of controllers that perfectly cooperate with the presented engines.
 |
 |
 |
Features
- Motor type: with plastic gear
- Gear: 200:1
- Supply voltage: 3 to 12 V (typical 6 V)
- Speed: 51 RPM
- Maximum torque: 7.2 kg*cm
- Minimum current consumption: 0.07 A
- Maximum current consumption: 0.8 A
- Shaft diameter: 7 mm
- Dimensions: 64,4 x 22,3 x 21 m
- Weight: 32 g
195506
Data sheet
- DC motor power
- Other
- Gear material
- Plastic
- Gear ratio
- 200:1
- Rotation speed
- 51 RPM
- Shaft diameter
- 7 mm
- Shaft shape
- Two sides flattened
- Obustronny wał silnika
- Nie
- Power supply voltage
- 6V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Dual motor controller that allows you to control two DC motors with 2.7-10.8V voltage and 1.2A continuous current per channel. Pololu 2130
zł38.90
24h
Available quantity: 1
Available
Pololu Low-Voltage Dual Serial Motor Controller
zł158.61
24h
Available quantity: 1
Available
Compact and complete robot controller, containing the ATmega328P AVR microcontroller (with 32 KB of Flash memory and 2 KB of RAM memory) and a two-channel DC motor driver. Pololu 1220
zł92.57
24h
Available quantity: 1
Available
These aluminum gearmotor brackets let you securely mount our larger Pololu plastic gearmotors (228:1 offset, 120:1 offset, 200:1 90-degree, and 120:1 90-degree) to your project. These brackets are sold in pairs, and each bracket comes with two 1″ long and two 0.75″ long #2-56 screws for securing different size motors.
zł31.11
24h
Available quantity: 2
Available
These extended aluminum gearmotor brackets let you securely mount our larger Pololu plastic gearmotors (228:1 offset, 120:1 offset, 200:1 90-degree, and 120:1 90-degree) to your project. The extended “neck” on these brackets allows for a large variety of mounting options. These brackets are sold in pairs, and each bracket comes with two 1″ long #2-56 screws for securing motors to the bracket.
zł31.02
Delivery date unknown
No product available!
Other products in the same category (16)
High-power brushed DC motor, 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is offset from but parallel to the motor shaft, built-in safety clutch. Pololu 1512
Retired
No product available!
This compact, inexpensive plastic gearmotor (brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Retired
No product available!
Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in gray with metal
Retired
No product available!
Battery: Li-Ion; 3.7V; 1000mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13813
Retired
No product available!
No product available!
This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/16-step).
Retired
No product available!
Wheels fit 2 mm diameter output shafts such as the ones on our sub-micro plastic planetary gearmotors. Pololu - 2356
Retired
No product available!
JEKEN CE-6200A ultrasonic cleaner, with digitally adjustable working time, power 70 W and a capacity of 1.4 l. It is well suited for repair and maintenance of electronic components, PCBs, optical elements, as well as for the dissolution of polymers
Retired
No product available!
Rick Waldron, Anna Gerber, David Resseguie, Emily Rose, Susan Hinton, Sara Gorecki, Bryan Hughes, Andrew Fisher, Julian David Duque, Pawel Szymczykowski, Donovan Buck, Jonathan Beri, Kassandra Perch, Raquel Vélez, Lyza Danger Gardner
Retired
No product available!
The grapple is used for precise operations when replacing SMD and BGA circuits. It allows you to lift small electronic components without using tweezers
Retired
No product available!
Spray CLEANSER PCC 15 with a capacity of 150ml, with a brush is a reliable solution for cleaning printed circuit boards and soldering residues. MICROCHIP
Retired
No product available!
Spray CLEANSER PCC 15 with a capacity of 400ml, with a brush is a reliable solution for cleaning printed circuit boards and soldering residues. MICROCHIP
Retired
No product available!
No product available!
Dispensing needle for precise application of glue, flux with an inner diameter of 0.62mm and an external diameter of 0.9mm.
Retired
No product available!
Dosing needle for precise application of glue, flux with an inner diameter of 0.25 mm and an external diameter of 0.51 mm
Retired
No product available!
No product available!
Plastic gear motor 200:1, output shaft at 90°, operating voltage 6 V, current consumption from 0.07 A to 0.8 A, speed 51 RPM and a maximum torque of 7.2 kg*cm. Pololu 1120