 
        
           
        
          DRV8833 Dual Motor Driver is a compact dual DC motor driver. It allows to drive two DC motors with a voltage in the range of 2.7-10.8 V. The controller is based on the Texas Instruments DRV8833 chip, thanks to which 1.2 A (2 A peak) can be taken from each channel. The board has protection against reverse power connection and thermal protection.
Example wiring diagram

Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
TB6612FNG Dual Motor Driver Carrier
Dual motor controller that allows you to control two DC motors with 2.7-10.8V voltage and 1.2A continuous current per channel. Pololu 2130
 No product available!
DRV8835 Dual Motor Driver Carrier
Miniature medium-power, 6 V brushed DC motor with a 51.45:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. Pololu 2365
 No product available!
10:1 Micro Metal Gearmotor MP
 No product available!
75:1 Micro Metal Gearmotor MP
 No product available!
100:1 Micro Metal Gearmotor MP
A4990 Dual Motor Driver Carrier
DC motor controller powered with a voltage in the range of 1.8 to 10V with a maximum output current of 2.6A. Compatible with STM32 Nucleo. Shield is equipped with a connector compatible with the Arduino UNO R3 standard. STMicroelectronics X-NUCLEO-IHM13A1
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS
DC motor driver with an operating voltage from 6 to 60 V and a maximum continuous current of 300 A. It can communicate via USB, UART, RC or analog signal and allows for the implementation of a feedback loop. Pololu 3584
 No product available!
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5074
ESC RC controller module with FlySky receiver designed for two brush motors with a supply voltage from 2.5 to 5 V and a current consumption of 2 A
Pololu Simple High-Power Motor Controller 18v15
 No product available!
Pololu G2 18v25 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 30V. Current capacity of the module: 25A. The module has protection against back voltage and overvoltage. Pololu 1366
Tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor. Operating voltage range from 0 V to 11 V, built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature. Pololu 2990
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5077
Two-channel motor controller with L298N system with 4.8 ... 46V motor power supply and 2A current capacity per channel. It has a protection in the form of diodes. DFRobot DRI0002
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. Pololu 2507
 No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
 No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5042
 No product available!
The core of a small robot, either as an auxiliary controller atop a Raspberry Pi base or as a complete control solution on its own. Its Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader. This version does not include any through-hole components or connectors, allowing for customized assembly or standalone use. Pololu 3118
Module of a 4-channel driver of DC motors with RP2040 microcontroller. It allows the connection of encoders and is equipped with a QW/ST connector. Pimoroni PIM636
Module with the driver of motors TB6612FNG and driver PWM PCA9685 for Raspberry Pi Pico. It allows you to control the movement of 4 DC motors. Waveshare Pico-Motor-Driver
 
                    Dual motor controller that allows you to control two DC motors with 2.7-10.8V voltage and 1.2A continuous current per channel. Pololu 2130