- Out-of-Stock
AVT1689 A
ID: 208189
RELAY TIMER - PLATE
RELAY TIMER - PLATE
Producer: AVT
An uncomplicated device used to convert short-term pulses into impulses of a given, adjustable duration. Such impulses can come, for example, from any switches, which, if pressed, will trigger the relay for a pre-set time. The operating time of the relay can be continuously adjusted in the range from 1 to approx. 120 sec.
The system can be used to maintain the opening of the bolt in door locks or wickets, it can also be helpful in temporarily controlling the lighting acting as an automatic switch after the set time has elapsed.
The printed circuit board and documentation are included.
A detailed description in EP08 / 12 or 
208189
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
SmartLED Shield driver (V4) for SmartMatrix series displays, for use with Teensy 3.2, Teensy 3.5 and Teensy 3.6. It is also possible to connect LED Dotstar or APA102 displays. Adafruit 1902
Retired
No product available!
Add motion, direction and orientation sensing to your wearable FLORA project with this high precision 9-DOF sensors: 3-axis accelerometer, 3-axis magnetometer and 3-axis gyroscope. Adafruit 2020
Retired
No product available!
Ambient Light Sensor, SI1145, connects to the I2C bus pads. Adafruit 1981
Retired
No product available!
Extension for Raspberry Pi; communication module with RS-485 interface (DEV-13000). Module with the possibility of mounting the DB-9 socket, the socket should be purchased separately
Retired
No product available!
FreeSoC2 board has two processors on-board: a CY8C5868LTI-LP039 and a CY8C5888AXI-LP096. The former serves as a debugger/programmer for the latter, which is the target upon which your application code will be installed. Both parts contain a Cortex-M3 processor core, 256kB of flash memory, 64kB of SRAM, and 2kB of EEPROM. DEV-13229
Retired
No product available!
32-bit microcontroller with ARM Cortex-M4 core, XMC4200 family, 256kB Flash, VQFN-48, Infineon
Retired
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing mass measurement up to 5 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
The set allows introducing distance, ambient lighting and gesture analysis into the subject using the VL6180X sensor. NUCLEO-L053R8 plate in set with VL6180X expansion board. P-NUCLEO-6180X2
Retired
No product available!
Shield for STM32 Nucleo, has two MP34DT01-M digital microphones made in MEMS technology
Retired
No product available!
9-inch display with universal HDMI interface and 10-point multitouch capacitive screen
Retired
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
Retired
No product available!
Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns for sensors, controllers, power, etc. With the included “snap on” micro-controller mounts, you can attach an Arduino, Raspberry Pi, SparkFun RedBoard, or SparkFun RedBot Mainboard!
Retired
No product available!
Bluetooth module for mounting in SMD technology with a fully configurable UART interface - transfer speed up to 2 Mb / s. WRL-11786
ATTENTION! A newer version of this product is available.
Click to go to the product page
Retired
No product available!
The LCD Button Shield V2 attaches to your Arduino to provide a 16x2, black character, green back light LCD with a keypad consisting of 5 keys — select, up, right, down and left. With this shield you will be able to move through menus and make selections straight from one board attached to your Arduino without requiring a massive tower of shields. DEV-13293
Retired
No product available!
RELAY TIMER - PLATE