- Out-of-Stock
CNC DRILLER - POWER SUPPLY - PLATE
Producer: AVT
Once, to make the object look good and meet the standards, the machinist had to deal with the material. In manual production, without the use of machines, each manufactured object was in a sense different. Today, computer controlled machines are used for processing. These machines are called CNC (Computerized Numerical Control) in short. Controlling via a computer and the appropriate application allows for fast and precise material processing. Another advantage of this type of machining is the high repeatability of the manufactured objects. The controller has been designed in such a way that it can be supervised by a program called Mach3. Its demo version can be downloaded from: www.machsupport.com The program communicates with the machine via the LPT port which can be a drawback, because this connector is replaced by USB. On the other hand, Mach3 has minimal hardware requirements so that you can use a computer from a few years ago to control the milling machine, which you can buy for a small amount or even receive from computer scrap. This justifies that buying a modern, expensive PC for use in a dusty workshop does not make much sense.
Recommendations: CNC milling machine will be useful for modelers and DIY enthusiasts, it will also be an interesting addition to the electronics or electronic service workshop.
Power supply (AVT5358 / 3)
The printed circuit board and documentation are included.
A detailed description in EP08 / 12 or ![]()
Manufacturer
Responsible person
Intenso Pendrive with a capacity of 32 GB equipped with a USB 2.0 interface. Maximum read speed: 28 MB / s, maximum write speed: 6 MB / s
No product available!
Display with 7 "TFT LCD touch screen for Odroid C1 +, C2 and XU4 computers The display is equipped with HDMI interface for image display and USB for touch screen display resolution 800x480 pixels
No product available!
Patchcord UTP 5E Ethernet cable with a length of 2 m - gray, with 2xRJ45 connectors
No product available!
Display board for the STM32F407G-DISC1 set. Built-in display with a resistive touch panel, has. The set includes a flexible cable that allows you to attach to the expansion board STM32F4DIS-BB
No product available!
The Electronics Starter Package with a plastic organizer and three AVT sets for self-assembly. Equipped with the basic tools necessary for work
No product available!
No product available!
A set containing the Intel Edison platform and a dedicated development board that allows you to output GPIO ports and 2 USB (micro AB) sockets, connect power 7..15V and turn off the system using the button. EDI2BB.AL.K
No product available!
Intel Edison platform with built-in antenna. Intel Atom 500MHz processor, 1GB RAM, supply voltage 3.15..4.5V, I2C, I2S, SD Card, SPI, UART, USB interfaces. EDI2.SPON.AL.S
No product available!
INTEL EDI2ARDUIN.AL.K Intel Edison Kit For Arduino, Atom, Wi-Fi/BT Compatible Module, Integrated Wi-Fi, 4GB Memory
No product available!
Orange Pi Plus 2 H3 Quad Core 1.6GHZ 2GB RAM 4K Open Source Development Board Mini PC
No product available!
Rainbow Case (Type B) for Raspberry Pi
No product available!
No product available!
Flora NeoPixel 30 RGB LED Strip in Reel - White Backing, 5 meters. Adafruit 1376
No product available!
With the Pmod Adapter for myRIO, you can now connect your myRIO to the expansive selection of Pmods offered by Digilent. 6002-410-013
No product available!
KAmodEPAPER is a module with a clear and energy-saving EPD (e-Paper) display of the GDE035A3 series. Thanks to the derived control signals and integrated in the inverter module, the display control is simple and no additional power lines are required
No product available!
Provides a 300 tie breadboard and 50 tie bus bar on an expansion card compatible with the NI myRIO Expansion Port (MXP). 210-283
No product available!
CNC DRILLER - POWER SUPPLY - PLATE