- Out-of-Stock
New products
New products New products
zł301.74
24h
Dostępny
Available
Available
zł59.04
24h
Available
AVT5390 A
ID: 208681
RETRO STYLE CLOCK - PRINTED PLATE
RETRO STYLE CLOCK - PRINTED PLATE
Producer: AVT
Nowadays, programmable systems displace discrete digital circuits. Finding a clock design without a microcontroller seems to be very difficult, and yet not so long ago only electronic clocks were built in this way. Yes, these types of devices are complicated and can take a lot of electricity, but it's hard to deny their basic advantage - they work immediately after turning on the power. They do not require knowledge of any programming language but only a few elements of combinatorics.
Recommendations: we mainly recommend people who want to take a break from ubiquitous programming.
Basic information:
- power supply from the 230 Vac power grid
- measuring time in a 12-hour or 24-hour system
- adapted to supply from 50 or 60 Hz networks
- no quartz generator - the basis of time is the mains frequency
- without microcontroller and other programmable systems
- a printed circuit board and documentation in the set
A detailed description in EP4 / 13 or 
Attention! When starting up the system, special care should be taken because of the dangerous tensions present in life. If you have no experience or are afraid, ask someone who is familiar with it. Never lift, do not twist, do not touch the plate if it is connected to the mains!
If you make any changes to the layout, remove the plug from the socket!
208681
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
CONTROLLER POWER 230 VAC RECEIVER - A KIT FOR INDEPENDENT INSTALLATION
Delivery date unknown
No product available!
The eXtremestyle silicone cable (1.5m length) with Lightning connector. Allows you to charge the device and transfer data. eXtreme S15ULW
Retired
No product available!
Camera with CMOS NT99141 sensor with a resolution of 1288x728 px. It communicates via a parallel interface. ArduCAM U6044
Retired
No product available!
Do you fly in your dreams? Do you like the feeling? Once again Ugears makes the dream come true reaching out to the sky with its first ever aircraft model represented by two flying machines in one package. Introducing – The Aviator model.
The model has three modules: the airplane, the helicopter and the flight control tower. Choose between your aircraft, set one on the tower’s bar and you are good to fly. As a beginner pilot you might want to start with the helicopter which is not as difficult to control as the airplane. Easier to manipulate but no less exciting, your chopper has a cockpit with doors that open and shut, and three-blade main and tail rotors. UGears 70053
Retired
No product available!
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
Retired
No product available!
Brushless motor Turnigy D3536 / 6 1250KV type Outrunner (HK18227)
Retired
No product available!
No product available!
TF Cloud V1.0 is a wireless file transmission module that allows data transfer between a computer and a 3D printer without the need for an SD card. It is based on the ESP-12S module with the ESP8266 chip, ensuring stable data transmission via Wi-Fi.
Retired
No product available!
No product available!
No product available!
3-pin ARK mounting strip, 5.0 mm pitch. 301-5.0-03P-12-00A(H)-BL
Retired
No product available!
A small USB splitter allowing to connect up to 4 USB devices, powered from the USB port
Retired
No product available!
No product available!
Evaluation kit with LittleBee GW1N-1 FPGA chip. Offers 1152 LUTs and 864 Flip-Flops (FF). The board has an FPC connector for the display and a USB type C. Sipeed Lichee Tang Nano
Retired
No product available!
No product available!
RETRO STYLE CLOCK - PRINTED PLATE