- Out-of-Stock
Turnigy Accucel-8 150W 7A Balancer/Charger
ID: 213247
HK Turnigy Accucel-8 150W 7A Balancer/Charger (7523)
Turnigy Accucel-8 150W 7A Balancer/Charger (7523)
The Accucel-8150 is a Lipoly/LiFe battery charging workhorse. Capable of handling up to 8S, 7A or a maximum of 150W charging current plus it balances and discharges packs which is critical for keeping your expensive batteries in perfect condition.
This charger has a 12v input and can be used with a mains 12v power supply or your car battery when at the field.
TURNIGY Accucel chargers are built with quality components and produced in robotic pick-n-place SMT technology machines to produce a reliable and accurate charger.
You wont find a better priced quality 8 Cell charger!
The Accucell has various programming and charging modes and will accept and safely charge NiCd,Lilo, Lipo, LiFe, Pb batteries.
ATTENTION.
There are several chargers now entering the China market that look similar to the Accucel-8. These chargers are produced with cheaper FETs and unfortunately much less accurate and very unsafe. There has been reports of the copied chargers over-charging packs and not balancing correctly.
Our chargers have CE and RoHS certification, proving there safety. Plus, thousands of customers the world over have used our chargers with excellent success.
Your batteries are expensive. We understand this and thats why we will not carry low-quality charging devices.
"CONNECTION BREAK" : This indicates you need to have the discharge AND balance plugs connected. This unit charges through the discharge wires and balances through the balance wires. Connect all wires or you will get a "CONNECTION BREAK" message.
Spec.
Operating voltage range: 11.0~18.0Volt
Circuit power: max. 150W
Charge current range: 0.1~7.0A
Discharge current range: 0.1~5.0A
NiCd/NiMH battery cell count: 1~27 cells
Lithium bettery cell count: 1~8 Series
Pb battery voltage: 2 to 36V
Weight: 625g
Dimensions: 170X125X35mm
This charger has a JST-XH charge plug, which makes it compatible with Zippy, TURNIGY and any pack with a JST adapter, balance ports are for 3s~8s packs only.
Note: Power supply not included.
PRODUCT ID: Accucel8150
Download
| Hobbyking file downloads | |
| manual(1).pdf | 2540kb |
213247
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
Ambient Light Sensor, SI1145, connects to the I2C bus pads. Adafruit 1981
Retired
No product available!
Extension for Raspberry Pi; communication module with RS-485 interface (DEV-13000). Module with the possibility of mounting the DB-9 socket, the socket should be purchased separately
Retired
No product available!
FreeSoC2 board has two processors on-board: a CY8C5868LTI-LP039 and a CY8C5888AXI-LP096. The former serves as a debugger/programmer for the latter, which is the target upon which your application code will be installed. Both parts contain a Cortex-M3 processor core, 256kB of flash memory, 64kB of SRAM, and 2kB of EEPROM. DEV-13229
Retired
No product available!
32-bit microcontroller with ARM Cortex-M4 core, XMC4200 family, 256kB Flash, VQFN-48, Infineon
Retired
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing mass measurement up to 5 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
The set allows introducing distance, ambient lighting and gesture analysis into the subject using the VL6180X sensor. NUCLEO-L053R8 plate in set with VL6180X expansion board. P-NUCLEO-6180X2
Retired
No product available!
Shield for STM32 Nucleo, has two MP34DT01-M digital microphones made in MEMS technology
Retired
No product available!
9-inch display with universal HDMI interface and 10-point multitouch capacitive screen
Retired
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
Retired
No product available!
Shadow Chassis is a marvelously durable and modular robot platform from RobotZone. The chassis plates and mounts are cut from ABS plastic and utilize the Actobotics 0.77" and 1.50" hub patterns for sensors, controllers, power, etc. With the included “snap on” micro-controller mounts, you can attach an Arduino, Raspberry Pi, SparkFun RedBoard, or SparkFun RedBot Mainboard!
Retired
No product available!
Bluetooth module for mounting in SMD technology with a fully configurable UART interface - transfer speed up to 2 Mb / s. WRL-11786
ATTENTION! A newer version of this product is available.
Click to go to the product page
Retired
No product available!
The LCD Button Shield V2 attaches to your Arduino to provide a 16x2, black character, green back light LCD with a keypad consisting of 5 keys — select, up, right, down and left. With this shield you will be able to move through menus and make selections straight from one board attached to your Arduino without requiring a massive tower of shields. DEV-13293
Retired
No product available!
Nintendo DS Screen Kit joins two of our more unique products together to provide you with an easy means to equip your next project with touchscreen functionality. Inside each kit is one Nintendo DS Touchscreen and one SparkFun Touchscreen Connector Breakout. LCD-13631
Retired
No product available!
MG2639 SparkFun Cellular Shield is a perfect addition to any Arduino project that requires connectivity when there’s no WiFi or Ethernet access nearby. The ZTE MG2639 module, which this shield is built around, supports SMS, TCP, UDP, and can even be used to make or receive phone calls. CEL-13120)
Retired
No product available!
HK Turnigy Accucel-8 150W 7A Balancer/Charger (7523)