- Out-of-Stock
ODROID W
ID: 233703
Module compatible with Raspberry-Pi software
ODROID-In
ODROID-W is a miniature computing module that is fully compatible with Raspberry-Pi.
The W stands for:
- Wearable device development
- Widely applicable Internet of Things (IoT) development
- Workable DIY electronics prototyping
The ODROID-W measures a very small 60 x 36 x 7mm (2.4 x 1.4 x 0.3 "). new features and improvements over the original Raspberry Pi:
- Li + rechargeable battery charger and fuel gauge for portables, wearable and robots application
- Real Time Clock to keep accurate time
- 12-bit precision ADC to measure the dynamic voltage signals via two single-ended inputs
- DC / DC step-down converters for higher power efficiency
- DC / DC step-up converter for 5Volt rails (USB host and HDMI) from a Li-Polymer battery
- USB Host port can be placed on top or bottom as preferred
- DIY friendly 0.1inch / 2.54mm pitch IO connector (up to 32 GPIO ports) for handy prototyping
ODROID-W = RPI + RTC + ADC + UPS + Battery gauge with significant Minimalism 
233703
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The 10 W AC adapter provides 5 V and 2 A current. It is equipped with a 1 m cable with microUSB plug. Akyga AK-TB-23
zł26.90
Delivery date unknown
No product available!
Other products in the same category (16)
No product available!
No product available!
FLUX LED 7.62 x 7.62 [mm] 5mm WARM white 3600K, angle 90 degrees; light intensity 2200 mcd (20mA) (3.2V) 4.0 [lm]
Retired
No product available!
No product available!
No product available!
8-bit ultralow power touch sensing microcontroller with 16 Kbytes Flash, ProxSense™, timers, USART, SPI, I2C, STM, RoHS
Retired
No product available!
No product available!
The MAXimator is an entry-level evaluation board with modern Altera MAX10 FPGA. The board can interface to external peripheral modules via Arduino Uno Rev 3 connectors. It also features HDMI+CEC+DCC and VGA interfaces
Retired
No product available!
Kaczorek T., Dzieliński A., Dąbrowski W., Łopatka R.
Delivery date unknown
No product available!
AVT kit for self-assembly running lights. AVT795 B
Retired
No product available!
No product available!
The set consists of STM32 Nucleo NUCLEO-F302R8 plate with STM32F302R8 microcontroller, X-NUCLEO-IHM07M1 plate with BLDC L6230 three-phase motor controller and BR2804-1700kV engine
Retired
No product available!
No product available!
Wei-Bin Zhang
Delivery date unknown
No product available!
No product available!
MYIR MYC-JA5D44 is a single-board computer in the form of a card with SO-DIMM 200-pin connector. The SAMA5D44 processor from Atmel, based on Cortex-A5 cores, has been equipped. It can work with a maximum frequency of 600 MHz. It has 512 MB of DDR2 SDRAM, 512 MB of NAND Flash memory. GPIO ports, interfaces have been derived on the SO-DIMM 200-pin connector.
Retired
No product available!
Module compatible with Raspberry-Pi software