- Out-of-Stock
PiFace Relay+
ID: 317118
PiFace Relay Board for Raspberry Pi
Description
PiFace RELAY is a stackable and HATs compliant relay daughter card for Raspberry Pi B and newer models with a 40pin GPIO header. This board adds four relays with normally open and closed contacts to your Raspberry Pi that can switch loads up to 2Amps DC in your software programs. Stackable up to eight boards and HAT (Hardware Attached on Top) compliant means a huge amount of expansion.
PiFace RELAY comes with 3x pillars/stand-offs to support and mount on top of the Raspberry Pi and a extended 40-way connector. A downloadable suite of Python based software is available allowing users to interact with any connected devices.
Specific Applications: Lighting Control, Motor Control, Solenoid Control, Model Railway
Features
- Four relay outputs for on/off control of loads up to 20V, 1A DC
- Works with Raspberry Pi models B plus and A plus (Raspberry Pi models with the 40 pin GPIO header)
- Stack up to eight PiFace Relay plus boards
- HAT (Hardware Attached on Top) compliant
317118
You might also like
Raspberry Pi 1 model B + is a popular single board computer with Broadcom BCM2835 processor (700MHz, ARM1176JZF-S core) and 512 MB RAM. The computer runs under Linux (eg Raspbian). There are, among others, 4 USB ports, HDMI connector, camera connector
zł185.41
24h
Available quantity: 13
Available
PiFace Relay Motor Control Extra (Board) for Raspberry Pi
zł89.00
24h
Available quantity: 1
Available
Raspberry Pi 3 model B (Quad Core Broadcom BCM2837, 4x1.2GHz ARM Cortex-A53, RAM 1GB, 4xUSB, Ethernet, HDMI, Wifi, Bluetooth)
zł179.00
Delivery date unknown
No product available!
The Raspberry Pi 3 Model B+ is boasting a 64-bit quad core processor BCM2837B0 running at 1.4GHz, dual-band 2.4GHz and 5GHz wireless LAN, Bluetooth 4.2/BLE, faster Ethernet, and PoE capability via a separate PoE HAT
zł177.60
24h
Available quantity: 58
Available
Other products in the same category (16)
No product available!
No product available!
No product available!
A module that allows you to connect ArduCAM cameras with a CSI interface to a PC or minicomputers via the USB3.0 interface. It not only supports high-resolution, high-frame rate image sensors, but also a stereoscopic camera and IRCUT control functions. ArduCAM B0111
Retired
No product available!
No product available!
8-bit ST7 MCU, 4kB Flash, 256B RAM, 128B EEPROM, Lite Timer with Watchdog, Autoreload Timer with 32-MHz input clock, SPI, 10-bit ADC with Op-Amp, DIP20, RoHS
Retired
No product available!
Broadcast FM Radio Transceiver for Portable Applications, QFN20, Silicon Labs, RoHS
Retired
No product available!
Stanisław Osowski, Andrzej Cichocki, Krzysztof Siwek
Delivery date unknown
No product available!
Introduction to Digital Design. Block Diagram / Verilog Examples; Richard E. Haskell & Darrin M. Hanna
Retired
No product available!
Switched-mode AC Power supply 12V/2A with DC 5.5x2.1 connector and EU/UK/USA/AUSTRALIA plugs. It has anti-overload, anti-overvoltage, short circuit protection. Conform to the norm Energy efficiency Level VI. Length of output cable is 1.2m
Retired
No product available!
High voltage differential probe. It is characterized by good measurement parameters: with a 100 MHz band and an operating voltage up to 700 V. The probe has two attenuation factors: 10X and 100X. Micsig DP10007
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
NanoPi NEO2 Black is a board developed by FriendlyELEC for creators, hobbyists and fans. This is a variant of NanoPi NEO2 without image output, but with space for an eMMC module and a larger (1GB) amount of RAM.
Retired
No product available!
PiFace Relay Board for Raspberry Pi