- Out-of-Stock
Universal ISP programmer for SPLD, CPLD and FPGA circuits (Altera, Atmel, Lattice, Xilinx) and AT89Sxxxx microcontrollers
Universal ISP programmer for SPLD, CPLD and FPGA circuits (Altera, Atmel, Lattice, Xilinx) and AT89Sxxxx microcontrollers
ZL11PRG is an extremely universal programmer, with which you can program and configure in the system (ISP) programmable circuits SPLD, CPLD and FPGA companies: Altera, Atmel, Lattice and Xilinx and some microcontrollers from Atmel. The programmer works with standard firmware included on the CD-ROM.
The ZL11PRG programmer emulates four popular ISP programmers:
ByteBlaster MV from Altera
In this mode you can program and configure CPLD (MAX3000A, MAX7000 - all families, MAX9000) and FPGA (FLEX6K, FLEX8K, FLEX10K, APEX II, APEX 20K, ACEX 1K and other systems powered with voltage not less than 2.5V).
In this mode the ZL11PRG programmer can work with the following programs and design systems: Max + Plus II, Quartus II, ASAP, Quartus II Programmer, ispVM System, Atmel ISP and WebPack XC9500 Programmer (v 3.3).
Lattice ispDOWNLOAD
With it, you can program Lattice PLD systems equipped with JTAG interface (most FPGA systems and all modern CPLD, as well as ispGDX2, ispGDX, ispGAL22LV10 / 22V10A etc.) and Lattice ISP (older generation PLD systems, such as ispGDS, ispPAC , ispGAL22V10, ispLSI1000 / 2000, etc.).
In this mode, the ZL11PRG programmer can work with the ispVM System.
DLC5 Programmer (Parallel Cable III)
In this mode, you can program and configure CPLD systems (XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3) and FPGA (Spartan XL, Spartan II, Virtex II).
In this mode of operation, the ZL11PRG programmer is supported by all Xilinx project packages, including free WebPack.
AT89ISP from Atmel
In this operating mode, all CPLD systems from the ATF1500 family (equipped with an ISP interface) from Atmel and microcontrollers AT89Sxxxx (family 8051) can be programmed in the system.
In this mode, the ZL11PRG programmer is supported by Atmel ISP (PLD programming) and AT89ISP (programming of AT89Sxxxx microcontrollers).
The set includes:
Bluetooth audio receiver module that allows wireless transmission of sounds. It is equipped with a PCB antenna and edge connectors
No product available!
Sound card in the form of a small device with a USB plug. It uses the ES9018K2M DAC, headphone amplifier and has a 3.5mm Jack audio output
No product available!
The case is made of ABS, designed for Raspberry Pi Zero W minicomputers. The user has free access to all minicomputer ports, including the GPIO connector
No product available!
The case is made of ABS, designed for Raspberry Pi Zero W minicomputers. The user has free access to all minicomputer ports, including the GPIO connector
No product available!
The case is made of ABS, designed for Raspberry Pi Zero W minicomputers. The user has free access to all minicomputer ports, including the GPIO connector
No product available!
Aluminum case designed for Raspberry Pi Zero minicomputers. The user has free access to all minicomputer ports
No product available!
Audio recorder module that allows for multiple recording and playback of sounds
No product available!
A power supply dedicated to the analysis of energy consumption by devices in embedded systems. Based on ESP32, it allows you to transfer data to a computer via a USB interface. Odroid SmartPower 3
No product available!
Audio preamplifier based on NE5532 chips. Equipped with an input selector function. Display and remote control included
No product available!
Stereo audio preamplifier based on the LM1036N chip. It allows you to control the bass, treble and volume level
No product available!
Class A power amplifier with one channel (mono) with the power of 25 W. Built on the basis of the popular design by J. Hood from 1969. The set includes 2 pieces
No product available!
A stereo tube preamplifier based on 6K4 tubes. Designed for use with active speakers or an additional amplifier and passive speakers. FX-AUDIO Tube-03
No product available!
A stereo tube preamplifier based on 6K4 tubes. Designed for use with active speakers or an additional amplifier and passive speakers. FX-AUDIO Tube-03 SUCA-AUDIO Tube-T1
No product available!
Stereo tube preamplifier based on 6J3 tubes. Designed for use with active speakers or an additional amplifier and passive speakers
No product available!
A stereo tube preamplifier based on 6K4 tubes. Designed for use with active speakers or an additional amplifier and passive speakers. SUCA-AUDIO TUBE-T1
No product available!
Class A tube preamplifier based on 6J1 tubes. Designed for use with an additional power amplifier. Powered by AC 12 V
No product available!
Universal ISP programmer for SPLD, CPLD and FPGA circuits (Altera, Atmel, Lattice, Xilinx) and AT89Sxxxx microcontrollers