.png)
- Out-of-Stock
Triple-Axis Digital-Output Gyro Breakout - ITG-3200
ID: 557766
SEN-11977
SEN-11977 Triple-Axis Digital-Output Gyro Breakout - ITG-3200
Description:
This is a breakout board for InvenSense’s ITG-3200, a groundbreaking triple-axis, digital output MEMS gyroscope. The ITG-3200 features three 16-bit analog-to-digital converters (ADCs) for digitizing the gyro outputs, a user-selectable internal low-pass filter bandwidth, and a Fast-Mode I2C (400 kHz) interface. Additional features include an embedded temperature sensor and a 2% accurate internal oscillator.
The ITG-3200 can be powered at anywhere between 2.1 and 3.6 V. For power supply flexibility, the ITG-3200 has a separate VLOGIC reference pin (labeled VIO), in addition to its analog supply pin (VDD) which sets the logic levels of its serial interface. The VLOGIC voltage may be anywhere from 1.71 V min to VDD max. For general use, VLOGIC can be tied to VCC. The normal operating current of the sensor is just 6.5 mA.
Communication with the ITG-3200 is achieved over a two-wire (I2C) interface. The sensor also features a interrupt output, and an optional clock input. A jumper on the top of the board allows you to easily select the I2C address, by pulling the AD0 pin to either VCC or GND; the board is shipped with this jumper tied to VCC. If you don’t plan on using the CLKIN pin, you can short the jumper on the bottom of the board to tie it to GND.
This breakout board is shipped as shown in the images. Note that there are two unpopulated resistors on the I2C lines, these can be added later by the customer if desired.
Not sure which gyro is right for you? Our Accelerometer and Gyro Buying Guide might help!
Dimensions:
- 0.87 x 0.72" (22.22 x 18.48mm)
Features:
- Digital-output X-, Y-, and Z-Axis angular rate sensors (gyros) on one integrated circuit
- Digitally-programmable low-pass filter
- Low 6.5mA operating current consumption for long battery life
- Wide VDD supply voltage range of 2.1 V to 3.6 V
- Standby current: 5 μA
- Digital-output temperature sensor
- Fast Mode I2C (400kHz) serial interface
- Optional external clock inputs of 32.768 kHz or 19.2 MHz to synchronize with system clock
- Pins broken out to a breadboard friendly 7-pin 0.1" pitch header
557766
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Other products in the same category (16)
A module that allows you to connect ArduCAM cameras with a CSI interface to a PC or minicomputers via the USB3.0 interface. It not only supports high-resolution, high-frame rate image sensors, but also a stereoscopic camera and IRCUT control functions. ArduCAM B0111
Retired
No product available!
A small minicomputer with a RockChip RK3328 quad-core SoC chip (ARM Cortex-A53). The computer is equipped with 1 GB DDR4 RAM, Gigabit Ethernet port and USB 3.0. Each module has its own unique MAC address. NanoPi NEO3 1GB
Retired
No product available!
A small minicomputer with a RockChip RK3328 quad-core SoC chip (ARM Cortex-A53). The computer is equipped with 2 GB DDR4 RAM, Gigabit Ethernet port and USB 3.0. Each module has its own unique MAC address. NanoPi NEO3 2GB
Retired
No product available!
White case for the NanoPi NEO3 minicomputer. It allows easy access to the Ethernet connector, USB, microSD cards and the power connector. FriendlyELEC Case for NEO3
Retired
No product available!
HDMI to CSI-2 bridge module based on TC358840 chip. It has a 22-pin FPC connector with a pitch of 0.5 mm and an audio connector. The input signal is supplied through the HDMI connector. Auvidea 70511
Retired
No product available!
Image capture module for Raspberry Pi. Captures high definition video from digital (HDMI/DVI), analog (YPbPr component) and computer (RGB) sources in 480p, 720p and 1080p. Picapture HD1
Retired
No product available!
3.5-inch TFT LCD display with case designed for Raspberry Pi. The display with a resolution of 320x480 px is equipped with a resistive touch screen. ArduCAM U611101
Retired
No product available!
Case dedicated to minicomputers Cubieboard and Cubieboard 2. Cubieboard Deluxe Case
Retired
No product available!
Development kit with Artix-7 100T FPGA chip, compatible with the PC/104 standard. The set is equipped with 512 MB DDR3 memory, Zmod port and Pmod ports. Digilent 410-398
Retired
No product available!
GPS module with u-blox ZED-F9R. Uses Automotive Dead Reckoning (ADR) technology. Provides highly accurate and continuous positioning by combining the 3D IMU sensor, vehicle dynamics model, correction data and GNSS measurements. SparkFun GPS-16475
Retired
No product available!
GPS module with u-blox ZED-F9R. Uses Automotive Dead Reckoning (ADR) technology. Provides highly accurate and continuous positioning by combining the 3D IMU sensor, vehicle dynamics model, correction data and GNSS measurements. SparkFun GPS-16344
Retired
No product available!
Module with 4 relays controlled by the I2C interface. Each relay can switch currents up to 40 A at 28-380 V AC. SparkFun KIT-16833
Retired
No product available!
ActivePresenter is a handy tool for creating interactive e-learning training, quizzes, software simulations or even educational games
Retired
No product available!
A small USB-UART TTL converter module based on the CH340N chip with a microUSB connector. Equipped with a LED indicating power.
Retired
No product available!
16-channel logic analyzer with a maximum sampling frequency of 100 MHz. It can decode data under most popular communication protocols. Works with Windows systems. LA1016
Retired
No product available!
USB camera module with a resolution of 8 MP based on a Sony IMX179 1/3.2" matrix compatible with UVC. It has a variable focal length adjustable in the range from 2.8 to 12 mm. Equipped with a CS mount lens with an integrated UV filter. ArduCAM UB0226
Retired
No product available!
SEN-11977