- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
Sparkfun Load Cell Amplifier - HX711
ID: 558997
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230
Description:
The SparkFun Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the amplifier to your microcontroller you will be able to read the changes in the resistance of the load cell and with some calibration you’ll be able to get very accurate weight measurements. This can be handy for creating your own industrial scale, process control, or simple presence detection.
The HX711 uses a two wire interface (Clock and Data) for communication. Any microcontroller’s GPIO pins should work and numerous libraries have been written making it easy to read data from the HX711. Check the hookup guide below for more information.
Load cells use a four wire wheatstone bridge to connect to the HX711. These are commonly colored RED, BLK, WHT, GRN, and YLW. Each color corresponds to the conventional color coding of load cells:
- Red (Excitation+ or VCC)
- Black (Excitation- or GND)
- White (Amplifier+, Signal+, or Output+)
- Green (A-, S-, or O-)
- Yellow (Shield)
The YLW pin acts as an optional input that is not hooked up to the strain gauge but is utilized to ground and shield against outside EMI (electromagnetic interference). Please keep in mind that some load cells might have slight variations in color coding.
Features:
- Operation Voltage: 2.7V-5V
- Operation Current: < 1.5mA
- Selectable 10SPS or 80SPS output data rate
- Simultaneous 50 and 60Hz supply rejection
Download
558997
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Aluminum extensometer beam, allowing measurement of weight up to 20 kilograms. It has four wires. It is used in kitchen scales and portable scales, it has a 21 cm cable, RoHS.
zł41.34
24h
Available quantity: 5
Available
The module allows you to attach a strain gauge (working in the Wheatstone bridge circuit) and convert the analog signal into its digital representation, available on the module output lines. The system processes the signal with a 24-bit resolution and can be powered by 2.7V - 5.5V. The module is especially recommended for constructing digital scales in combination with Arduino
zł4.82
24h
Available quantity: 17
Available
Other products in the same category (16)
No product available!
Programmable BT4.0 module with UART 2x4 pin 2.54 mm UART connector
Retired
No product available!
No product available!
No product available!
No product available!
Orange Pi NAS expansion card makes it possible to transform an Orange Pi Zero into a file sharing server by plugging in an external SATA hard drive
Retired
No product available!
Velleman kit for self-assembly of an ultrasonic bats detector. K8118
Retired
No product available!
Printed circuit board and programmed circuit for a remote radio switch. AVT5590 A +
Retired
No product available!
AVT kit for self-assembly remote radio switch. AVT5590 B
Retired
No product available!
No product available!
Orange Pi ABS Transparent Protective Case for Orange Pi Plus 2e
Retired
No product available!
The device for automatic control of lighting or other electrical devices. Installed in place of an ordinary wall switch. He reacts to movement
Retired
No product available!
The OpenMV M7 Camera is a small, low-power microcontroller board that allows you to easily implement applications using machine vision in the real world. The best part about the OpenMV is that it is not only capable of image capture, but also face detection, color tracking, QR code reading and plenty more. SparkFun SEN-14186
Retired
No product available!
The SparkFun micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. This breakout board for the micro:bit’s edge connector allows to connect the micro:bit to breadboards and other sensors, motors, LEDs and more! BOB-13989
Retired
No product available!
No product available!
Camera for computer Banana Pi M2+, with sensor CMOS 5 Megapixels (OV5640). BPI-M2+ camera module
Retired
No product available!
Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. SEN-13230