- Out-of-Stock
New products
New products
zł67.99
24h
Available
zł69.00
24h
Available
zł67.99
24h
Available
Available
zł79.00
24h
Available
zł67.99
24h
Available
zł69.00
24h
Available
zł67.99
24h
Available
Available
zł79.00
24h
Available
Pololu 3214 - 9.7:1 Metal Gearmotor 25Dx48L mm HP 12V with 48 CPR Encoder
ID: 562781
This gearmotor consists of a high-power, 12 V brushed DC motor combined with a 9.68:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 464.64 counts per revolution of the gearbox’s output shaft.
Overview:
These cylindrical brushed DC gearmotors are available in a wide range of gear ratios and with five different motors (two power levels of 6V motors and three power levels of 12V motors). The gearmotors all have the same 25 mm diameter case and 4 mm diameter gearbox output shaft, so it is generally easy to swap one version for another if your design requirements change (though the length of the gearbox tends to increase with the gear ratio). All versions are also available with an integrated 48 CPR quadrature encoder on the motor shaft. Please see the 25D metal gearmotor comparison table for detailed specifications of all our 25D metal gearmotors. This dynamically-sortable table can help you find the gearmotor that offers the best blend of speed, torque, and current-draw for your particular application. A more basic comparison table is available below:
| Rated Voltage | Motor Type | Stall Current @ Rated Voltage | No-Load Speed @ Rated Voltage | Approximate Stall Torque @ Rated Voltage |  With Encoder |  Without Encoder |
|---|---|---|---|---|---|---|
| 6 V | high-power (HP) |
6.5 A | 10,000 RPM | 5 oz-in | 1:1 HP 6V w/encoder | |
| 2150 RPM | 20 oz-in | 4.4:1 HP 6V w/encoder | 4.4:1 HP 6V | |||
| 990 RPM | 39 oz-in | 9.7:1 HP 6V w/encoder | 9.7:1 HP 6V | |||
| 460 RPM | 75 oz-in | 20.4:1 HP 6V w/encoder | 20.4:1 HP 6V | |||
| 280 RPM | 90 oz-in | 34:1 HP 6V w/encoder | 34:1 HP 6V | |||
| 200 RPM | 115 oz-in | 47:1 HP 6V w/encoder | 47:1 HP 6V | |||
| 130 RPM | 150 oz-in | 75:1 HP 6V w/encoder | 75:1 HP 6V | |||
| 97 RPM | 210 oz-in | 99:1 HP 6V w/encoder | 99:1 HP 6V | |||
| 56 RPM | 350 oz-in | 172:1 HP 6V w/encoder | 172:1 HP 6V | |||
| 6 V | low-power (LP) |
2.4 A | 6200 RPM | 2 oz-in | 1:1 LP 6V w/encoder | |
| 1300 RPM | 8 oz-in | 4.4:1 LP 6V w/encoder | 4.4:1 LP 6V | |||
| 590 RPM | 17 oz-in | 9.7:1 LP 6V w/encoder | 9.7:1 LP 6V | |||
| 290 RPM | 33 oz-in | 20.4:1 LP 6V w/encoder | 20.4:1 LP 6V | |||
| 170 RPM | 50 oz-in | 34:1 LP 6V w/encoder | 34:1 LP 6V | |||
| 120 RPM | 65 oz-in | 47:1 LP 6V w/encoder | 47:1 LP 6V | |||
| 78 RPM | 95 oz-in | 75:1 LP 6V w/encoder | 75:1 LP 6V | |||
| 58 RPM | 130 oz-in | 99:1 LP 6V w/encoder | 99:1 LP 6V | |||
| 34 RPM | 200 oz-in | 172:1 LP 6V w/encoder | 172:1 LP 6V | |||
| 25 RPM | 220 oz-in | 227:1 LP 6V w/encoder | 227:1 LP 6V | |||
| 15 RPM | 300 oz-in | 378:1 LP 6V w/encoder | 378:1 LP 6V | |||
| 11 RPM | 400 oz-in | 499:1 LP 6V w/encoder | 499:1 LP 6V | |||
| 12 V | high-power (HP) |
5.6 A | 10,200 RPM | 5.5 oz-in | 1:1 HP 12V w/encoder | |
| 2250 RPM | 23 oz-in | 4.4:1 HP 12V w/encoder | 4.4:1 HP 12V | |||
| 1030 RPM | 44 oz-in | 9.7:1 HP 12V w/encoder | 9.7:1 HP 12V | |||
| 500 RPM | 85 oz-in | 20.4:1 HP 12V w/encoder | 20.4:1 HP 12V | |||
| 290 RPM | 120 oz-in | 34:1 HP 12V w/encoder | 34:1 HP 12V | |||
| 210 RPM | 165 oz-in | 47:1 HP 12V w/encoder | 47:1 HP 12V | |||
| 130 RPM | 240 oz-in | 75:1 HP 12V w/encoder | 75:1 HP 12V | |||
| 100 RPM | 300 oz-in | 99:1 HP 12V w/encoder | 99:1 HP 12V | |||
| 12 V | medium-power (MP) |
2.1 A | 7800 RPM | 2.7 oz-in | 1:1 MP 12V w/encoder | |
| 1700 RPM | 11 oz-in | 4.4:1 MP 12V w/encoder | 4.4:1 MP 12V | |||
| 770 RPM | 22 oz-in | 9.7:1 MP 12V w/encoder | 9.7:1 MP 12V | |||
| 370 RPM | 42 oz-in | 20.4:1 MP 12V w/encoder | 20.4:1 MP 12V | |||
| 220 RPM | 63 oz-in | 34:1 MP 12V w/encoder | 34:1 MP 12V | |||
| 160 RPM | 85 oz-in | 47:1 MP 12V w/encoder | 47:1 MP 12V | |||
| 100 RPM | 125 oz-in | 75:1 MP 12V w/encoder | 75:1 MP 12V | |||
| 76 RPM | 165 oz-in | 99:1 MP 12V w/encoder | 99:1 MP 12V | |||
| 43 RPM | 250 oz-in | 172:1 MP 12V w/encoder | 172:1 MP 12V | |||
| 33 RPM | 320 oz-in | 227:1 MP 12V w/encoder | 227:1 MP 12V | |||
| 12 V | low-power (LP) |
1.1 A | 5600 RPM | 2 oz-in | 1:1 LP 12V w/encoder | |
| 1200 RPM | 8 oz-in | 4.4:1 LP 12V w/encoder | 4.4:1 LP 12V | |||
| 560 RPM | 15 oz-in | 9.7:1 LP 12V w/encoder | 9.7:1 LP 12V | |||
| 260 RPM | 29 oz-in | 20.4:1 LP 12V w/encoder | 20.4:1 LP 12V | |||
| 150 RPM | 43 oz-in | 34:1 LP 12V w/encoder | 34:1 LP 12V | |||
| 110 RPM | 60 oz-in | 47:1 LP 12V w/encoder | 47:1 LP 12V | |||
| 71 RPM | 85 oz-in | 75:1 LP 12V w/encoder | 75:1 LP 12V | |||
| 55 RPM | 115 oz-in | 99:1 LP 12V w/encoder | 99:1 LP 12V | |||
| 31 RPM | 180 oz-in | 172:1 LP 12V w/encoder | 172:1 LP 12V | |||
| 23 RPM | 240 oz-in | 227:1 LP 12V w/encoder | 227:1 LP 12V | |||
| 14 RPM | 320 oz-in | 378:1 LP 12V w/encoder | 378:1 LP 12V | |||
Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. For these gearboxes, the recommended upper limit for instantaneous torque is 200 oz-in (15 kg-cm); we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of a second) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.
In general, these kinds of motors can run at voltages above and below their nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
Dimensions:
| Size: | 25D x 60L mm |
|---|---|
| Weight: | 95 g |
| Shaft diameter: | 4 mm |
General specifications:
| Gear ratio: | 9.68:1 |
|---|---|
| Free-run speed @ 12V: | 1030 rpm |
| Free-run current @ 12V: | 300 mA |
| Stall current @ 12V: | 5600 mA |
| Stall torque @ 12V: | 44 oz·in |
| Free-run speed @ 6V: | 515 rpm1 |
| Stall current @ 6V: | 2800 mA1 |
| Stall torque @ 6V: | 22 oz·in1 |
| Lead length: | 8 in2 |
| Motor type: | 5.6A stall @ 12V (HP 12V) |
| Encoders?: | Y |
Notes:
- 1 This motor will run at 6 V but is intended for operation at 12 V.
- 2 May vary by a few inches.
562781
Data sheet
- Engine size (series)
- Other
- DC motor power
- HP
- Gear material
- Metal
- Gear ratio
- 9.7:1
- Rotation speed
- 1030RPM
- Shaft shape
- D
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Dual VNH3SP30 Motor Driver Carrier MD03A
zł1,212.68 24hAvailable quantity: 2 AvailableAdapter that allows you to easily mount the wheels on a motor with a shaft diameter of 4 mm using screws size 4-40. The hub fits both round and D-shaped shafts. Pololu 1081
zł36.60 24hAvailable quantity: 2 AvailablePololu Universal Aluminum Mounting Hub for 4mm Shaft, M3 Holes (2-Pack)
zł41.14 24hAvailable quantity: 2 AvailableA set of adapters (adapter) from the popular 4 mm to 12 mm motor shaft, wheel holders from RC models. Pololu 2684
zł22.80 24hAvailable quantity: 2 AvailableThese aluminum gearmotor brackets let you securely mount Pololu’s 25D mm metal gearmotors to your project. The brackets are sold in pairs, and each bracket includes two M3 screws for securing the motor to the bracket. Each bracket also features seven mounting holes and twelve mounting slots for M3 or #4-size screws (not included), giving you a variety of mounting options.
zł38.78 24hAvailable quantity: 3 Available
Other products in the same category (16)
Digital ECHO effect for use in audio systems. MK182
Retired No product available!
No product available!
No product available!
MP3 player module controlled by the I2C interface. It is based on a class D amplifier with a power of 1.4 W. The board has a 3.5 mm headphone output and an 8 Ω speaker connector. Audio files are saved on the microSD card. SparkFun DEV-15165
Retired No product available!
No product available!
- Valentin Afraimovich, Edgardo Ugalde, Jesus Urias Delivery date unknown
No product available!
No product available!
No product available!
Expansion module kit with Arduino compatible connectors for building a Zumo robot. The module includes a dual engine controller, buzzer and user button, as well as a 3-axis accelerometer and compass. Pololu 2508
Retired No product available!
The break-out board for the Arduino 101 LGA module. Just like the YUN, it integrates an ATmega32U4 and an Atheros AR9331 with WiFi and Linino OS. A000126
Retired No product available!
HK XT60 Male w/ 12AWG Silicon Wire 10cm (5pcs/bag) (10254)
Retired No product available!
8-bit ST7 MCU, 8kB Flash, 384B RAM, Lite Timer, Autoreload Timer, SPI, LINSCI, 10-bit ADC, DIP20, RoHS
Retired No product available!
Kintex™-7 FPGA ACDC 1.0 Base Board (Acquisition, Contribution, Distribution and Consumption) By Inrevium™, RoHS
Retired No product available!
- George Greene, Young Cho, James Hartnett, Avram Bar-Cohen Delivery date unknown
No product available!
No product available!
Audio expansion module designed for Odroid C2, C1+ and C4 minicomputers. Equipped with a DAC I2S converter and two RCA connectors and a Toslink connector. Hardkernel HiFi Shield 2
Retired No product available!
This gearmotor consists of a high-power, 12 V brushed DC motor combined with a 9.68:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 464.64 counts per revolution of the gearbox’s output shaft.