- Out-of-Stock
Raspberry Pi 3 & MathWorks Set Learn to Program Pack
ID: 563053
Raspberry Pi 3 & MathWorks Learn to Program Pack is a set consisting of a Raspberry Pi 3 computer with necessary hardware and MATLAB & Simulink Student Suite software. The set is designed for modeling and implementing solutions based on Raspberry Pi 3 in MATLAB and SIMULINK environments
Description
Raspberry Pi 3 & MathWorks Learn is an official element14 set for students to help you start designing a new device. MathWorks MATLAB and Simulink Student Suite is a professional environment and tools available for the student to enable modeling, simulation and analysis of projects in the design phase, and then programming the device using the same tool as engineers and scientists on a daily basis.
Raspberry Pi 3 model B was built on the basis of Broadcom 2837 ARMv8 64bit processor. It is a faster and more powerful computer than its predecessors, it also has built-in wireless communication systems such as WiFi and Bluetooth.
The kit allows you to start working immediately after receiving it. Perform the implementation of the layout model using RPi 3 in the Symulink program and check its operation in reality.
Kit contents
- Raspberry Pi 3
- The book "MATLAB and Simulink Student Suite" in English
- Micro SD card with adapter and NOOBS system installed
- Power supply with interchangeable connectors for different network sockets standards
- Housing for RPi 3
563053
Other products in the same category (16)
NanoPi M4V2 is a FriendlyELEC single board computer. It uses LPDDR4 RAM memory and adds among others: POWER and RECOVERY micro switches and a microphone input.
Retired
No product available!
NanoPI NEO is a single-board chip from FriendlyELEC with a RAM of 256 MB, successfully competing with the systems created by the giant in this field Raspberry Pi. It is 25% smaller and cheaper than the Raspberry Pi Zero board with similar capabilities
Retired
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
Retired
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
Retired
No product available!
The SparkFun Qwiic Shield for Arduino Nano allows you to add the SparkFun Qwiic ecosystem to development boards that use the Arduino Nano Footprint in an easy-to-assemble shield. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Arduino Nano to four SparkFun Qwiic connectors.
Retired
No product available!
The SparkFun Qwiic Shield for Thing Plus provides an easy-to-assemble way to add the SparkFun Qwiic ecosystem to any development board with the Thing Plus Footprint. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Thing Plus to four SparkFun Qwiic connectors. Sparkfun DEV-16138
Retired
No product available!
Cytron 0.8Amp 5V-26V DC Motor Driver Shield - DC motor driver for Arduino
Retired
No product available!
No product available!
No product available!
No product available!
Cytron USB to UART Converter CH340 - USB - UART converter based on the CH340 chip
Retired
No product available!
Logic level converter (4 channels)
Retired
No product available!
The Blebox Wifi controller is dedicated to the most modern digital tapes with 5 V and 12 V, but a LED strip with WS2812 / WS2811 driver is required. BleBox pixelBox
Retired
No product available!
Evaluation kit with RISC-V Dual Core 64bit chip clocked at 400MHz. Equipped with a USB-UART converter, camera, display and Micro SD card connectors. Designed for AI applications in IoT. Seeed Studio 102991150
Retired
No product available!
Evaluation kit with RISC-V Dual Core 64bit chip clocked at 400MHz. Equipped with a USB-UART converter, OV2640 camera, LCD display. The set is enclosed in a housing. Designed for AI applications in IoT. Seeed Studio 110991191
Retired
No product available!
MEMS MSM261S4030H0 microphone module designed to work with Sipeed MAix kits. The module is characterized by high sensitivity, low noise and low cost. Seeed Studio 107990153
Retired
No product available!
Raspberry Pi 3 & MathWorks Learn to Program Pack is a set consisting of a Raspberry Pi 3 computer with necessary hardware and MATLAB & Simulink Student Suite software. The set is designed for modeling and implementing solutions based on Raspberry Pi 3 in MATLAB and SIMULINK environments