- Out-of-Stock
USB Load Tester - adjustable USB load
ID: 564007
Adjustable USB load displaying voltage and current consumption of connected devices. The load can draw current up to 3 A. The voltage is measured in the range 3.5 ... 21V, current 0 ... 4A. It is also possible to measure cell capacity
Description
Adjustable USB load displaying voltage and current consumption of connected devices. The load can draw current up to 3 A. The voltage is measured in the range 3.5 ... 21 V, current 0 ... 4 A. It is also possible to measure cell capacity.
properties
- Operating voltage: 3.5 ... 21 V
- Compatible with Qualcomm QuickCharge 2.0
- Load current: 0 ... 3 A
- Current measurement: 0 ... 4 A
- Current measurement error: <3% + 2mA
- Load control with two potentiometers: for roughing and fine adjustment in the range of ± 0.2 A
- Connectors: USB type A, Mini USB, Micro USB, USB type C, Lightining
- Symmetrical USB type A plug (eliminates the need to insert the device into the USB port from the right side)
- The possibility of adding an additional load via a USB connection
- Possibility to connect the load to sources other than USB through the ARK connector
- Maximum load power: 35 W
- The fan is activated when the temperature exceeds 55 ° C
- OLED display
564007
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
No product available!
The controller can control two brush motors, communicating with the master system using USB Micro-B, TTL serial interface, analog signals, as well as signals from the RC apparatus. The current capacity of 5A / channel allows you to control high-power motors. Polol 2394
Retired
No product available!
EEPROM CAT93C86LI-G memory; 16kbit; 2K x 8bit; access time: 150ns; Power supply: 1.8 ... 5.5 V; 8-Pin PDIP
Retired
No product available!
Nettemp Pi Hat is a module that allows to connect eight trees of sensors with I2C/1-Wire interface and control of four relays outputs. Thanks to the extension board is possible to build in an easy way e.g. a multipunkt temperature controller.
Retired
No product available!
32GB microSDHC Memory Card with SD Adapter, class 10 A1, Kingston
Retired
No product available!
WiFi 802.11 b / g / n module with ESP8266 system, 5 leads are available with 2 mm pitch with the possibility of soldering of gold pins, power lines, reset line and UART interface have been led to the connector. 3.3V power supply
Retired
No product available!
WiFi 802.11 b / g / n module with ESP8266 system, 8 pins with 2.54 mm pitch are available with soldered gold pins, 3 GPIO lines, reset, power supply and UART interface on the connector. U.FL. Antenna Connector 3.3 V power supply
Retired
No product available!
nRF51 DK is a development board based on the nRF51422 system with Bluetooth Low Energy (BLE) and 2.4 GHz connectivity. The module has a connector compatible with Arduino shields, buttons and diodes available to the user.
Retired
No product available!
No product available!
No product available!
Featuring a quad-core Amlogic processor, advanced Mali GPU, and Gigabit Ethernet
Retired
No product available!
The case has openings for all outputs including the GPIO port making it a great fit for projects that are connected to external hardware.
Retired
No product available!
The case has openings for all outputs including the GPIO port making it a great fit for projects that are connected to external hardware.
Retired
No product available!
Super charged single board computer with an Octa-core processor and 2GB of RAM. Along side the elite processing unit, it features Gigabit Ethernet, 2 USB, SATA, WiFi, Bluetooth, and HDMI connection. It can run on a variety of operating systems including Android, Lubuntu, Ubuntu, Debian, and Raspbian
Retired
No product available!
Works with the ODROID-C2 / C0 / C1+. The HiFi Shield provides both stereo RCA connectors and a 3.5mm stereo jack (all gold-plated) to connect to external amplifiers and other audio equipment
Retired
No product available!
This rev of the RS232 Shield provides with the option to choose between two pins from an Arduino (D0 to D7) as software serial ports to communicate with RS232 Shield. DEV-13029
Retired
No product available!
Adjustable USB load displaying voltage and current consumption of connected devices. The load can draw current up to 3 A. The voltage is measured in the range 3.5 ... 21V, current 0 ... 4A. It is also possible to measure cell capacity