P-NUCLEO-IOD01A1 - STM32 Nucleo pack for IO-Link device fully compatible with IO-Link v1.1 (PHY and stack)
ID: 572181
5906623436217
zł375.22
Tax included
zł305.06 tax excl.
The P-NUCLEO-IOD01A1 is an STM32 Nucleo pack composed of the NUCLEO-L073RZ development board, the STEVAL-IOD003V1 evaluation board and the X-NUCLEO-IKS01A2 expansion board
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The P-NUCLEO-IOD01A1 is an STM32 Nucleo pack composed of the NUCLEO-L073RZ development board, the STEVAL-IOD003V1 evaluation board and the X-NUCLEO-IKS01A2 expansion board.
The STEVAL-IOD003V1 offers an IO-Link device PHY layer (L6362A) while the NUCLEO-L073RZ runs an IO-Link demo stack (developed by and property of TEConcept Gmbh) compatible with rev 1.1 and firmware controlling the X-NUCLEO-IKS01A2 sensors.
The STM32 Nucleo pack provides an affordable and easy-to-use solution for the development of IO-Link and SIO applications, L6362A communication features and robustness, together with the STM32L073RZT6 computation performance.
Features
- Equipped with Arduino UNO R3 connectors and compatible with STM32 Nucleo boards:
- STEVAL-IOD003V1IO-Link (PHY) device layer based on L6362AOperating voltage range 6.5 to 35 VDedicated CQ overload pin (wake-up)Diagnostics pin (UVLO, over-temperature and cut-off)UART interfaceLinear regulators for independent supply from +24 V bus (12 mA 3.3 V and 100 mA 12 V)LEDs for status and diagnosticsOverload and overheating protections with non-dissipative cut-off functionFull reverse polarity on IO-Link interface pinsEMC protections according to IO-Link v1.1 and IEC 60947-5-2Ground and VCC wire break protections
- X-NUCLEO-IKS01A2LSM6DSL 3D accelerometer and 3D gyroscopeLSM303AGR 3D accelerometer and 3D magnetometerLPS22HB pressure sensorHTS221 capacitive digital relative humidity and temperatureDIL24 socket for additional MEMS adapters and other sensorsFree comprehensive development firmware library and samples for all sensors compatible with STM32Cube firmware
- NUCLEO-L073RZ
- STM32L073RZT6 32-bit microcontroller based on ARM® Cortex®-M0+ core
- Pre-programmed IO-Link device stack (v1.1 compatible)
- Arduino UNO R3 connectivity and ST morpho extension pin headers
- Mbed-enabled (http://mbed.org)
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
572181
You might also like
STM32 Nucleo-64 development board with STM32L073RZT6 MCU, supports Arduino and ST morpho connectivity
zł79.15
24h
Available quantity: 8
Available
Motion MEMS and environmental sensor expansion board for STM32 Nucleo, equipped with Arduino UNO R3 connector layout; designed around the LSM6DSL 3D accelerometer and 3D gyroscope, the LSM303AGR 3D accelerometer and 3D magnetometer, the HTS221 humidity and temperature sensor and the LPS22HB pressure sensor. The board interfaces with the STM32 microcontroller via the I²C pin
Delivery date unknown
No product available!
Available
Other products in the same category (16)
The X-NUCLEO-IKS02A1 industrial motion MEMS sensor expansion board is compatible with the Arduino UNO R3 connector layout. STMicroelectronics X-NUCLEO-IKS02A1
zł133.00
24h
Available quantity: 2
Available
The X-NUCLEO-EEPRMA1 expansion board is based on M24xx I²C and M95xx SPI EEPROM for data reading and writing
zł97.37
24h
Available quantity: 1
Available
Expansion module with color sensor VD6283. The cap is compatible with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-6283A1
zł202.48
24h
Available quantity: 2
Available
An expansion board designed for the STM32 Nucleo based on the Teseo-VIC3DA, a global navigation satellite system (GNSS) chip. STMicroelectronics X-NUCLEO-GNSS2A1
zł284.87
24h
Available quantity: 3
Available
Expansion board for STM32 Nucleo based on S2-LP RF transmitter operating in 868MHz band. The expansion board is compatible with ST morpho and Arduino UNO R3 connectors. STMicroelectronics X-NUCLEO-S2868A2
zł161.81
24h
Available quantity: 3
Available
The X-NUCLEO-STMODA1 provides an easy way to expand your STM32 Nucleo board with the STMod+ connector, which allows interaction with the new set of STM32 Nucleo development boards using this connector
zł119.72
24h
Available quantity: 1
Available
The STEVAL-FKI433V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP
zł368.37
24h
Available quantity: 1
Available
Extension board with distance sensor ToF VL53L1, The sensor has a range of up to 400 cm. The kit includes 2 modules with sensors that can be connected via a 10-pin connector. The shield is compatible with STM32 Nucleo boards and has an Arduino UNO R3 connector. STMicroelectronics X-NUCLEO-53L1A2
zł202.48
24h
Available quantity: 2
Available
The X-NUCLEO-IHM17M1 is a low voltage three-phase brushless DC motor driver expansion board based on the STSPIN233 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
zł86.24
24h
Available quantity: 6
Available
An expansion board with digital outputs (for industrial applications) designed to work with the STM32 Nucleo kits. The module is based on the IPS161HF double high-side switch. STMicroelectronics X-NUCLEO-OUT10A1
zł209.46
24h
Available quantity: 1
Available
The X-NUCLEO-IHM15A1 dual brush DC motor driver expansion board is based on the STSPIN840 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of compact motor driving applications such as thermal printers, robotics and toys
zł89.38
24h
Available quantity: 3
Available
Expansion board for STM32 Nucleo with NFC card reader based on ST25R3916B chip. The board includes a connector compatible with the Arduino Uno R3. STMicroelectronics X-NUCLEO-NFC08A1
zł192.97
Delivery date unknown
No product available!
Expansion board with a distance sensor ToF VL53L5CX with a matrix of 64 pixels and a range of up to 4 m. The shield is compatible with STM32 Nucleo boards. STMicroelectronics X-NUCLEO-53L5A1
zł202.48
24h
Available quantity: 1
Available
Board with digital outputs designed to work with STM32 Nucleo. It is based on the IPS1025H-32 single high-side switch circuit. STMicroelectronics X-NUCLEO-OUT06A1
zł272.33
24h
Available quantity: 1
Available
The X-NUCLEO-LPM01A is a 1.8 V to 3.3 V programmable power supply source with advanced power consumption measurement capability
zł419.11
24h
Available quantity: 2
Available
Expansion board with LCD TFT 2.2 "display for STM32 Nucleo sets. Equipped with SPI NOR Flash 64Mbit memory for storing images and a joystick for GUI navigation. STMicroelectronics X-NUCLEO-GFX01M2
zł197.22
24h
Available quantity: 3
Available
The P-NUCLEO-IOD01A1 is an STM32 Nucleo pack composed of the NUCLEO-L073RZ development board, the STEVAL-IOD003V1 evaluation board and the X-NUCLEO-IKS01A2 expansion board