WEP 992DA + soldering station

Description

• Hot air , used for desoldering and soldering electronic circuits, eg BGA, SMD and etc. Blowing in the station is obtained by means of a compressor
• Stronger tipped flask with peak power 72-75W (original Hakko heating element of Japanese production)
• Extracting the vapors from under the grotówki

WEP 992DA + soldering station is suitable for soldering and desoldering electronic components such as: SOIC, CHIP, QFP, PLCC, BGA, SMD, etc. (especially mobile phones).

WEP 992DA + soldering iron is a hot air soldering station and soldering iron. The station is equipped with a PID microprocessor, which checks the station operation parameters in 20ms cycles and corrects them to the set values.

Temperature values, airflow power, operating mode are visible on a large, readable LCD display, which greatly simplifies the work.

The hotair soldering iron is equipped with a ceramic heating element that quickly and evenly heats up. The heater is made of hard alloys, allowing long working time at high temperatures, without being subject to deformation, this significantly increases the stability of work and extends the life of the heater.

In the holder for the hot air flask there is a micro-contact which, when the flask is put down, causes it to go into standby mode, by cooling the heating element, and then switching off the air flow. This extends the life of the heater and saves electricity.

The station is equipped with functions to control proper operation, we receive messages about short circuit in the circuit, overload of circuits, failure to obtain the set temperature. All these errors are displayed on the display.

Selecting the automatic operation mode, when we put the hot air flask on the stand, the device will automatically stop heating and will cool down to a safe temperature. Thanks to this, we will take care of the long, trouble-free operation of the heating element, energy savings and security of the service.

The soldering iron is distinguished by such functions:

• 3 Work programs. The soldering station has the ability to store 3 work programs for hot air and a flask. Depending on the type of work, assembly and disassembly, we set the appropriate program.
• Operation of hot air in automatic / manual mode. Selecting the automatic operation mode, when we put the hot air flask on the stand, the device will automatically stop heating and will cool down to a safe temperature. Thanks to this, we will take care of the long, trouble-free operation of the heating element, energy savings and security of the service. Choosing manual mode, when we often have to solder something, then we save time and increase work efficiency. It is recommended to switch to automatic mode before finishing work.
• Temperature correction function. Depends on the working environment, the efficiency of the heating element, the power of the blow, the grotto's use, all this affects the correct temperature correction to obtain the given parameter.
• Work in C / F mode. It is possible to set the display in which units the temperature will be displayed.
• Sleep function for soldering iron. The soldering iron is equipped with a sleep mode, when the flask is not used, after a preset time from 0-99min it goes into sleep mode, ie the flask is heated to 200C, it prevents over-oxidation of the mainsail, which affects its lifetime and heating element. We have the option of disabling the mode by setting 0.
• A tipped flask with a heating element that heats up quickly, maintains a stable temperature and is electrostatically safe.
• Extract of vapors from the soldering flask smoke generated during the soldering process is immediately sucked out, providing the user with a healthy, ecological work environment.

properties

• Technical data:
  • Voltage: 220-240 V
  • Power consumption: 720W
  • Operating environment from 0 to 50 ° C
  • Compact design with a legible LCD display
  • PID controller
  • Microprocessor control of parameters: temperature, power of blowing, working time, temperature correction
  • Protection against reaching too high temperature and alerting
  • Possibility to store 3 work programs (temperature, power of the blow)
  • Cooling function
  • Temperature display mode F / C
• Hot air station:
  • Air flow source: compressor
  • Air flow: up to 28 L / min
  • Smooth temperature regulation in the entire range
  • Temperature range: 100-480 ° C
  • Temperature stability: +/- 1 ° C
  • Display type: LCD
  • Cord length in the flask: up to 90 cm
  • Manual / automatic mode
  • Protection against reaching too high temperature and alerting
  • Displays the real power of the blow
• Main station:
  • Temperature range: 200-480 ° C
  • Temperature stability: +/- 1 ° C
  • Peak power: 72-75W
  • Display type: LCD
  • Earth resistance below 2ohm
  • Potential relative to ground below 2mV
  • System: ESD safe
  • The length of the flask wire: up to 100 cm
  • Sleep mode: switched on after idle operation 0-99 minutes

Included:

• WEP 992DA + soldering station with fume extractor
• Stand for the hotair flask
• A set of nozzles:
  • round nozzle 2.5 mm diameter 1124
  • round nozzle with a diameter of 4.4 mm 1130
  • round nozzle with a diameter of 6 mm 1196
  • round nozzle with a diameter of 9 mm 1197
  • square nozzle 12x12 mm 1313
• Stand for the tipped flask with a cleaning sponge
• Graduated flask 908B with TB tip with extract of fumes
• Gripper for lifting systems
• Power cord