Category: STARTER KITS, PROGRAMMERS, MODULES

Single board computer with SOM module NXP i.MX 8M processor, has 1 GB of RAM, 8GB of eMMC memory, wireless communication and TPU coprocessor. It includes numerous connectors, including USB 2.0 / 3.0 ports, DSI interface, CSI-2, Ethernet port, audio connectors and a 40-pin GPIO connector. Coral Dev Board G950-01455-01

Development board equipped with Bluetooth 5.0 module with nRF52840 chip. It has connectors that are compatible with Arduino and Raspberry Pi HAT shields. Waveshare NRF52840 Eval Kit

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477

The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927

WiFi module developed by AI-Thinker Co., Ltd with ESP8266 processor. Integrates a 32-bit MCU microcontroller with 80 MHz clock, RTOS support, Wi-Fi and antenna. The module supports the IEEE802.11 b / g / ni standard and has a complete TCP / IP protocol stack. AI-Thinker ESP-12S

Prototyping kit dedicated to micro:bit. It offers pin leads, a contact plate, buttons, LEDs and a buzzer. SB Components 22717

Module with round 1.28" IPS LCD display and 240x240 px resolution and ESP-12E chip. SB Components 24025

Module with OTP-538U non-contact temperature sensor. The board is equipped with a Grove connector and has analog outputs. Seeed Studio 101020062

Starter kit with 10 basic Grove modules and Base Shield V2 extension designed to work with Arduino boards. The user has at his disposal a number of lessons to get to know the possibilities of the set. Seeed Studio 103030375

SoM (System on Module) module with STM32MP157C chip. It integrates the Arm® Cortex®-A7 dual-core processor and the Arm® Cortex®-M4 coprocessor, as well as the PMIC power supply, 512 MB RAM and 4 GB eMMC memory. Seeed Studio 102110318

Module with light sensor - LS06-S phototransistor. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020173

Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265

RA4M1-Zero is a compact development board with an RA4M1 microcontroller, integrated USB interface, encryption support, and analog-digital peripherals. Designed for SMT mounting, it is suitable for serial solutions and projects requiring limited space.

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. Adafruit 3179

Tomasz Frenchman

Expansion board with LCD TFT 2.2" display for STM32 Nucleo-144 sets. Equipped with SPI NOR Flash 64Mbit memory for storing images and a joystick for GUI navigation. STMicroelectronics X-NUCLEO-GFX02Z1

Isolated UART-RS485 converter designed for M5Stack sets. It allows communication within an industrial serial interface. M5Stack U094

Pmod PIR is a module with a PIR motion sensor (EKMC1601111), which allows you to detect motion up to 5 meters from the module. The sensor during operation is characterized by low power consumption. Digilent 410-389

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 16 MB of QSPI flash memory. The system can be programmed in C/C++ or microPython. SparkFun DEV-17745