Category: STARTER KITS, PROGRAMMERS, MODULES

ESP32-P4-WIFI6-Touch-LCD-4C board with a 4″ round AMOLED display, 10-point touch support, Wi-Fi 6, Bluetooth 5, and hardware security features, designed for advanced embedded applications, HMI systems, voice-enabled devices, and smart interfaces.

ESP32-P4-WIFI6-Touch-LCD-3.4C development board with a 3.4-inch AMOLED display, Wi-Fi 6 and Bluetooth 5 (LE) support, two microphones with echo cancellation, and hardware security features. A solution for AI, HMI, and IoT projects requiring high performance and precise touch interaction.

Development kit allowing the development of applications using the STM32H7 microcontroller with ARM Cortex-M7 core and Cortex-M4 (dual core). The Pmod, STMod + and Arduino Uno V3 connectors allow you to add external peripherals. STMicroelectronics STM32H747I-DISCO

Espressif ESP32-C3FH4 WiFi module board with RISC-V core. It offers 4 MB Flash memory and 400 kB SRAM and an RGB LED. It has a built-in ceramic WiFi/BLE antenna. Waveshare ESP32-C3-Zero-M

The XTS-FMC module is an extension for FPGA devices that allows access to communication channels via the SMA connector. P0401

Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460

Module with ATmega32u4 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The microcontroller is clocked at 8 MHz and works at 3.3 V. Adafruit 3076

Development kit with STM32F334C8T6 microcontroller (64 KB Flash, 16 KB RAM) and built-in programmer/debugger ST-Link/V2-1

Battery with a capacity of 190 mAh designed to power the M5ATOM series modules. M5Stack T001

Function module designed for MicroMod boards. It allows you to add LoRa and LoRaWAN wireless communication in the 915 MHz frequency band to the project. SparkFun DEV-18573

Function module designed for MicroMod boards. It combines the SGP40 (air quality), SHTC3 (temperature and humidity) and STC31 (CO2 concentration) sensors and communicates via the I2C interface. SparkFun DEV-18632

Development board with the ESP-WROOM-02 WiFi module. The board has a USB-UART converter, a basket for a Li-Ion 18650 battery and a charging circuit

The expansion module is designed to work with the micro:bit educational board. It allows you to build an electronic piano

Extension board designed for MicroMod main modules. Equipped with the ZED-F9P GNSS receiver. It can receive data from GPS, GLONASS, Galileo and BeiDou systems. SparkFun DEV-17722

Development board with WiFi and Bluetooth ESP32 module. It has been equipped with industrial interfaces RS485 and CAN. TTGO T-CAN485 ESP32

Mini board with RP2040 microcontroller equipped with two ARM Cortex-M0 + 133 MHz cores, 264 kB RAM. The board also has 8 MB of QSPI flash memory. The circuit can be programmed in C/C++, CircuitPython or MicroPython. Pimoroni SP011

The IO expansion module is designed to work with the micro:bit educational board. There are 20 IO pins on the board, a buzzer, audio output and voltage stabilization circuit

IO expansion module designed for use with the micro:bit educational development board. The board exposes 20 IO pins along with 3.3 V power and GND lines, enabling direct connection of sensors and electronic modules. The design includes a built-in passive buzzer and a voltage stabilization circuit allowing the module to be powered via a 6–12 V DC connector or a microUSB port

Compact ISP programmer for AVR microcontrollers. Works with the Arduino IDE. USBtinyISP