Category: STARTER KITS, PROGRAMMERS, MODULES

Miniature development board with ATtiny817 microcontroller. It has analog inputs, PWM outputs and two STEMMA QT connectors. Adafruit 5233

Development board with WiFi and Bluetooth module Espressif ESP32-WROVER. It is equipped with a microSD card slot, a USB-UART converter and a Li-Ion battery charging system. TTGO T8 V1.1 ESP32

I2C-CAN converter using the MCP2551 and MCP2515 systems and the ATmega168PA microcontroller. The module uses the I2C bus and the Grove connector for communication. Seeed Studio 113020111

The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001

Module with a 10 kΩ digital potentiometer based on the DS3502 chip. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4286

Development kit based on ATSAMD51 with WiFi and BLE 5.0. It is equipped with a 2.4-inch LCD screen, IMU (LIS3DHTR), microphone, buzzer, microSD card slot, light sensor and infrared transmitter (IR 940nm). Seeed Studio 102991299

A precise barometric pressure and temperature sensor, ideal for altimetry and environmental applications. It can detect changes in height as small as 1.5 cm and offers high relative accuracy of ±6 Pa. It supports I2C and SPI interfaces for flexible integration with microcontrollers. The pre-assembled module with STEMMA QT connectors facilitates quick connection in drones, wearable devices, and IoT projects. Adafruit 6411

Base plate designed for NodeMCU (ESP8266 WIFI). The module is an expansion board that allows you to plug the NodeMCU into the slot and use the Grove sensor ports. Seeed Studio 105020008

Compact development kit from the M5StickC series equipped with ESP32 Pico and display. Includes accessories for building a watch. M5Stack K016-H

A mini module with a Qwiic connector designed for Raspberry Pi minicomputers. Qwiic SHIM uses a unique connector that snaps into the GPIO connector for a secure, solder-free connection. SparkFun DEV-15794

The ATAVRSBIN1 module enables the implementation of 9DoF inertial systems in the AVR Xplain environment. Integrated MEMS sensors and ready-to-use software libraries allow for quick startup of projects in the fields of automation, robotics, and motion analysis.

Board with the WiFi Espressif ESP32-S3 module. It offers 8 MB of Flash memory and 512 KB of SRAM and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5426

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477

Module with an 8-channel ADC converter with 8-bit resolution. It uses the ADS7830 chip and is equipped with a STEMMA QT connector, thanks to which it communicates via the I2C interface. Adafruit 5836

Module with WiFi and BLE Espressif ESP32-S3 system and LCD TFT display. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5483

Moduł z nadajnikiem-odbiornikiem dedykowany do komunikacji przez światłowód. Pozwala przesyłać dane na odległość do 10 km przy pomocy protokołu UART. DFRobot TEL0153

Advanced programmable logic controller (PLC) based on ESP32-S3, designed for industrial, automation and remote monitoring applications. It offers 8 optically isolated digital inputs, 4 relay outputs, PWR-CAN and PWR-485 interfaces and the ability to communicate with the EZDATA cloud. With wide power supply options, display, sensors and easy integration with Grove sensors, it is a comprehensive solution for IoT and automation systems. M5Stack K141

A versatile extension for Adafruit Feather boards, allowing you to quickly connect Grove modules and Stemma QT accessories without soldering. The module offers three Grove A/D connectors, one UART, and two I2C connectors, making it easy to expand your project with a variety of sensors and interfaces. An additional Stemma QT port allows for further expansion of I2C devices. Adafruit 5862

ESP32-S2-DevKitC-1 is a development board with Wi-Fi, ideal for IoT projects and breadboard prototyping. Espressif ESP32-S2-DevKitC-1-N8R2

The analog pH meter, specially designed for Arduino controllers, with the connector (Gravity series). It has an LED which works as the Power Indicator, a BNC connector and PH2.0 sensor interface. The pH measurements at ± 0.1pH (25?). SEN0161