- New
zł249.08 tax excl.
Makerbase MKS Monster8 V2.0 32-bit motherboard designed for FDM/FFF 3D printers, featuring an STM32F407VET6 microcontroller running at 168 MHz, 512 KB Flash memory and 192 KB RAM. Supports a 12 V to 24 V DC supply, eight stepper motor driver sockets, nine motor connectors, four heater outputs and three PWM fan channels. Features USB-C, CAN and microSD interfaces and supports Marlin and Klipper firmware. The Suit 1 kit includes the motherboard, 38 configuration jumpers and a 1 m USB-A to USB-C cable. Makerbase MKS Monster8 V2.0 Suit 1
The MKS Monster8 V2.0 motherboard from Makerbase is designed to control FDM/FFF 3D printers, including machines using CoreXY kinematics. The controller features a 32-bit STM32F407VET6 microcontroller with an ARM Cortex-M4 core running at 168 MHz, 512 KB Flash memory and 192 KB RAM. The board coordinates stepper motor movement, controls heating systems and fans, and reads signals from printer sensors. It supports Marlin 2.x and Klipper firmware, making it suitable for building new machines and upgrading the control electronics of existing 3D printers, including Voron designs.
The MKS Monster8 V2.0 operates with a 12 V to 24 V DC power supply and features eight sockets for replaceable StepStick-format stepper motor drivers. The sockets provide STEP, DIR and ENABLE signals, as well as UART and SPI communication lines for configuring compatible motor drivers. The board provides nine motor connectors controlled through eight driver sockets, with two connectors sharing one driver. The configuration supports motion axes and extruders in 3D printers with complex mechanical arrangements. DIAG diagnostic signal connections are also provided on the PCB for implementing sensorless homing.
The controller provides four heater control outputs, including the H-BED heated bed output and HE0, HE1 and HE2 heater outputs. Temperature is monitored through four measurement inputs, TB, TH0, TH1 and TH2, designed for connecting appropriate temperature sensors. The board features three PWM-controlled fan channels and three non-PWM fan power outputs. Fan output voltage can be selected using jumpers between VIN, 12 V and 5 V, according to the PCB markings. The MKS Monster8 V2.0 also features protection circuits for MOSFET control and temperature measurement, using resistors and Schottky diodes.

For communication and data storage, the board features a USB-C connector, a USB flash drive socket and a microSD (TF) card slot. The controller includes an integrated CAN transceiver and CAN bus connector, along with USART and I2C communication connections. The built-in 4 KB EEPROM stores configuration data. EXP1 and EXP2 connectors, signal lines and a display interface connector are also provided. USB device functionality enables communication with a computer, while firmware updates can be performed through the DFU interface, a microSD card or a USB flash drive.
The MKS Monster8 V2.0 features six endstop inputs, a 3D Touch bed levelling sensor connector and a NeoPixel LED strip control output. The board also provides signals for external motor drivers, communication connections and an independent 5 V power output rated at up to 3 A. The controller features replaceable fuses, reverse polarity protection and TVS overvoltage protection. The motor circuits also include components that reduce the effects of back electromotive force generated during motor operation. Connector placement and printed PCB labels help identify individual circuits during printer installation and configuration.
The MKS Monster8 V2.0 Suit 1 kit includes the motherboard, 38 configuration jumpers and a 1 m USB-A to USB-C cable. The jumpers are used to select motor driver communication modes and configure selected voltages and board functions. Stepper motor driver modules are not included. Before starting the controller, the jumpers must be configured correctly, power supply polarity and pin assignments checked, and firmware settings matched to the connected printer components.
Expansion board for three stepper motor drivers compatible with Arduino Nano. The stepper driver connectors fit A4988 modules
Extension module for building a 3D printer or CNC machine. Designed to work with Arduino Mega and A4988 stepper motor drivers
Universal control module designed for 3D printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays, LED strips and temperature sensors. BIGTREETECH Manta M5P
Universal control module designed for 3D printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays, LED strips and temperature sensors. BIGTREETECH Manta M5P
Universal control module designed for 3D printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays, LED strips and temperature sensors. BIGTREETECH Manta M8P V1.1
A control module designed specifically for Ender 3 printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays and temperature sensors as well as an EZ connector. BIGTREETECH Manta E3EZ V1.0
A universal control board for a 3D printer based on the 32-bit STM32F429ZE microcontroller. It allows you to connect 8 stepper motors with an operating voltage of up to 60 V and 8 cooling fans. Supports proximity sensor and BL Touch sensor support. BIGTREETECH Octopus Pro V1.0 (F429)
Control module designed specifically for Ender 3, Ender 3 Pro, Ender 5, Ender 5 Plus and CR-10 printers. It is based on the STM32G0B1 microcontroller. It has a built-in interface for connecting displays and temperature sensors. BIGTREETECH SKR MINI E3 V3.0
No product available!
Control module designed specifically for Voron V0 3D printers. It is based on the Raspberry Pi RP2040 microcontroller. It has a shape compatible with Raspberry Pi, so the minicomputer can be mounted directly on the module. BIGTREETECH SKR Pico V1.0
An expansion board equipped with three sockets compatible with stepper motor drivers. It has two EXP control interfaces and can work with motherboards used in 3D printers, e.g. BIGTREETECH SKR V1.3, BIGTREETECH SKR V1.4, BIGTREETECH SKR V1.4 Turbo. BTT EXP-MOT V1.0
No product available!
Extruder controller with CAN communication dedicated to 3D printers. It is designed to work with type 36 stepper motors and is a perfect solution for 3D printing enthusiasts and professionals who are looking for a reliable controller for precise control of the extruder. BIGTREETECH EBB36 CAN (MAX31865)
Extruder controller with CAN communication dedicated to 3D printers. It is designed to work with type 42 stepper motors and is a perfect solution for 3D printing enthusiasts and professionals who are looking for a reliable controller for precise control of the extruder. BIGTREETECH EBB42 CAN (MAX31865)
The Bigtreetech SKR v1.4 is a versatile and powerful motherboard for 3D printers, offering a wide range of features and support for various components. With compatibility for different stepper motor drivers and the ability to expand with WiFi connectivity, it is an excellent choice for anyone looking to optimize their 3D printer and tailor it to their specific needs. BIGTREETECH SKR V1.4
BIGTREETECH EBB SB2240 CAN V1.0 is a reliable and quiet controller module that, thanks to the latest TMC2240 chip, ensures high performance, safety, and long-lasting stable operation of your 3D printer. With extensive diagnostic capabilities and compatibility with popular control boards, it is an excellent solution for demanding users. BIGTREETECH EBB SB2240 CAN V1.0
The Octopus V1.1 is a versatile and powerful motherboard, ideal for advanced 3D printer users. With its robust processor, support for multiple interfaces, and the ability to control 8 axes, this motherboard offers extensive expansion and customization options to meet individual needs. BIGTREETECH Octopus V1.1
BIGTREETECH EBB SB2209 CAN V1.0 is a reliable and quiet controller module that, thanks to the TMC2209 chip, ensures high performance, safety, and long-lasting stable operation of your 3D printer. With extensive diagnostic capabilities and compatibility with popular control boards, it is an excellent solution for demanding users. BIGTREETECH EBB SB2209 CAN V1.0
Makerbase MKS Monster8 V2.0 32-bit motherboard designed for FDM/FFF 3D printers, featuring an STM32F407VET6 microcontroller running at 168 MHz, 512 KB Flash memory and 192 KB RAM. Supports a 12 V to 24 V DC supply, eight stepper motor driver sockets, nine motor connectors, four heater outputs and three PWM fan channels. Features USB-C, CAN and microSD interfaces and supports Marlin and Klipper firmware. The Suit 1 kit includes the motherboard, 38 configuration jumpers and a 1 m USB-A to USB-C cable. Makerbase MKS Monster8 V2.0 Suit 1