 
        
           
        
          The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface.
This tiny little board does all of the neat-o Arduino tricks that you're familiar with: 9 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 8MHz and 3.3V, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere. There is a voltage regulator on board so it can accept voltage up to 12VDC. If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
30:1 Micro Metal Gearmotor HP
 No product available!
4-digit 7-segment display with MAX7219 driver chip. Adafruit 1269
A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2981
I2C multiplexer module with TCA9548A system. Allows you to connect up to 8 devices. The system works like a gateway - it transmits I2C interface data to one of the 8 main busses. This allows you to connect up to 8 devices with the same address. Adafruit 2717
 No product available!
New 5MegaPixel AutoFocus CMOS camera module with JPEG output. The camera module is based on Omnivision OV5640 image sensor and can be used with ArduCAM shields and other platforms like Freescale i.MX6 develop board. ArduCam U3183
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
Base board compatible with Arduino. It was equipped with an Atmega 328P microcontroller. It has 14 I/O lines (including 6 PWM channels) and 6 analog inputs. SparkFun DEV-14525
Qduino Mini is a tiny, Arduino-compatible board with ATmega32u4 (8MHz, 32kB Flash, 2kB RAM), a LiPol battery connector and charger built-in. SparkFun DEV-13614
 No product available!
Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Arduino UNO kit. It has a USB C. The board also has a USB-UART converter, a microphone and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun DEV-15444
Development board with NXP iMXRT1062 ARM Cortex-M7 microcontroller. Equipped with a microSD slot. Version without Ethernet communication. PJRC TEENSY41-NE-PINS
Base board compatible with Arduino. It was equipped with the ATSAMD21G18 microcontroller. It has 26 I/O lines and 14 analog inputs. SparkFun DEV-14812
 No product available!
SparkFun DEV-10914 is a compact development board with an ATmega328 and 3.3 V logic level, equipped with basic protection and designed to work with an external USB–UART interface. It is suitable for applications requiring cooperation with low-voltage modules.
 No product available!
Development kit with ATSAMD51J20 microcontroller with ARM Cortex M4F core. It is clocked at 120 MHz, has 1 MB of Flash and 256 KB of SRAM. There are 6 SERCOM interfaces on the board. SparkFun DEV-14713
Development kit with SAMD21G18A microcontroller with ARM Cortex M0+ core and LoRa RFM95W radio communication module. SparkFun WRL-15836
IoT development board the size of Arduino, equipped with an ARM Cortex-M3 processor (STM32F205) and a Wi-Fi communication module (with an integrated antenna and uFL connector). SparkFun DEV-13321
A development board compatible with the Arduino Pro Mini. It is equipped with an ATSAMD21G18 microcontroller. It has 22 I/O lines and 14 analogue inputs. SparkFun DEV-13664
 No product available!
Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Feather kit. It has a USB C. The board also has a USB-UART converter, a microphone and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun WRL-15574
Evaluation kit with Bluetooth 5.0 Sparkfun Artemis module. Equipped with a microphone, kmaers and accelerometer. SparkFun DEV-16828
Development kit with ATSAMD21E microcontroller with ARM Cortex M0+ core. The chip can be clocked at 48 MHz, has a built-in 256 KB of Flash memory and 32 KB of SRAM. The module has a Qwiic connector. SparkFun DEV-15423
Base board compatible with Arduino. It was equipped with an ATmega328P microcontroller. It has 22 I / O lines (including 6 PWM channels) and 8 analog inputs and a Qwiic connector. SparkFun DEV-18158
 
                    Pro Micro is similar to Pro Mini Arduino compatible board, main difference is that Pro Micro uses ATmega32u4 with builtin USB connectivity. Sparkfun DEV – 12587