![Pro Micro - 5V/16MHz Pro Micro - 5V/16MHz](https://kamami.pl/31824-large_default/pro-micro-5v16mhz-sparkfun-dev-12640.jpg)
![Pro Micro - 5V/16MHz Pro Micro - 5V/16MHz](https://kamami.pl/31824-large_default/pro-micro-5v16mhz-sparkfun-dev-12640.jpg)
zł88.25 tax excl.
Pro Micro is similar to Pro Mini Arduino compatible board, main difference is that Pro Micro uses ATmega32u4 with builtin USB connectivity. Sparkfun DEV-12640
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface.
This tiny little board does all of the neat-o Arduino tricks that you're familiar with: 9 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere. There is a voltage regulator on board so it can accept voltage up to 12VDC. If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC.
Data sheet
30:1 Micro Metal Gearmotor HP
No product available!
DRV8835 Dual Motor Driver Carrier
I2C multiplexer module with TCA9548A system. Allows you to connect up to 8 devices. The system works like a gateway - it transmits I2C interface data to one of the 8 main busses. This allows you to connect up to 8 devices with the same address. Adafruit 2717
New 5MegaPixel AutoFocus CMOS camera module with JPEG output. The camera module is based on Omnivision OV5640 image sensor and can be used with ArduCAM shields and other platforms like Freescale i.MX6 develop board. ArduCam U3183
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
The Fio v3 is a new spin on the Arduino Fio hardware powered by the ATmega32U4. Not only is it small and LiPo-ready, it’s a very capable XBee-ready development board. DEV-11520
Development kit with ATSAMD21E microcontroller with ARM Cortex M0+ core. The chip can be clocked at 48 MHz, has a built-in 256 KB of Flash memory and 32 KB of SRAM. The module has a Qwiic connector. SparkFun DEV-15423
A small module, matching the breadboard, containing a 32-bit microcontroller with ARM Cortex M7 core. PJRC TEENSY40
No product available!
A small module matching the contact plate based on a 32-bit microcontroller with ARM Cortex M7 core. Has a microSD slot. PJRC TEENSY41
Base board compatible with Arduino. It was equipped with an Atmega 328P microcontroller. It has 14 I/O lines (including 6 PWM channels) and 6 analog inputs. SparkFun DEV-14525
The SparkFun AST-CAN485 board is a miniature Arduino in a compact Pro Mini housing with a built-in CAN (Control Area Network) and RS485 ports. Sparkfun DEV-14483
Evaluation kit with Bluetooth 5.0 Sparkfun Artemis module. Equipped with a microphone, kmaers and accelerometer. Himax HM01B0 camera included. SparkFun KIT-17071
A development board compatible with the Arduino Pro Mini. It is equipped with an ATSAMD21G18 microcontroller. It has 22 I/O lines and 14 analogue inputs. SparkFun DEV-13664
No product available!
Qduino Mini is a tiny, Arduino-compatible board with ATmega32u4 (8MHz, 32kB Flash, 2kB RAM), a LiPol battery connector and charger built-in. SparkFun DEV-13614
Development board with NXP iMXRT1062 ARM Cortex-M7 microcontroller. Equipped with a microSD slot. Version without Ethernet communication. PJRC TEENSY41-NE
Board with the ATmega328 microcontroller from the AVR family, there are 20 I/O lines, 6 PWM channels, 6 analog inputs at the user\'s disposal. SparkFun DEV-15123
Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Arduino Nano kit. It has a USB C. The board also has a USB-UART converter, a microphone, Lipo battery charging and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun DEV-15443
Pro Micro is similar to Pro Mini Arduino compatible board, main difference is that Pro Micro uses ATmega32u4 with builtin USB connectivity. Sparkfun DEV – 12587
No product available!
Base board compatible with Arduino. It was equipped with an ATmega328P microcontroller. It has 22 I / O lines (including 6 PWM channels) and 8 analog inputs and a Qwiic connector. SparkFun DEV-18158
Pro Micro is similar to Pro Mini Arduino compatible board, main difference is that Pro Micro uses ATmega32u4 with builtin USB connectivity. Sparkfun DEV-12640