DRV8876 (QFN) Single Brushed DC Motor Driver - DC motor driver
ID: 1179036
5906623413225
zł24.86
Tax included
zł20.21 tax excl.
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and current consumption up to 1.1 A. Pololu 4037
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Module with DC motor driver DRV8876. It allows you to control the movement of a DC motor with a voltage from 4.5 to 37 V and a current of up to 1.1 A (continuous current). The interface requires two control lines: PWM and GPIO in PH/EH mode or two PWM signals in In/IN mode. The use of one PWM signal allows you to limit the number of inputs needed for bidirectional motor movement, but such a solution does not support the braking function. The controller has built-in protection against reverse polarity, over voltage, overload and overheating, and has an integrated current sensor and active current regulation. The logical part can be supplied with the voltage from 1.8 to 5.5 V, thanks to which the module can work with voltages of 3.3 V and 5 V.
Pinout description
- VIN - supply voltage 4.5 - 37 V
- GND - ground
- VM - pin that gives access to the supply voltage of motors with reverse polarity protection
- OUT1, OUT2 - motor outputs
- EN/IN1 - control signal
- PH/IN2 - control signal
- PMODE - selection of control interface (PH/EN or IN/IN)
- IMODE - four-state input for current regulation and overcurrent protection mode
- FAULT - error output
- SLEEP - input to enter low power mode
- VREF - Reference Voltage of the Current Limiting Threshold
- CS - current sensor output
Features
- DRV8876 motor driver
- Speed and direction control
- The supply voltage of the motors: 4.5 to 37 V
- Supply voltage of the logic part: 1.8 to 5.5 V
- Motor current consumption: 1.1 A (continuous), 3.5 A (temporary)
- Reverse polarity, over voltage, overload and overheating protection
- Current sensor
- PH/EN or IN/IN interface
- Dimensions: 15.2 x 17.8 mm
Kit contains
- DRV8876 (QFN) Single Brushed DC Motor Driver
- 2 x male straight 1x7
1179036
Data sheet
- Output current
- 1,1 A
- Number of channels
- 1
- Supply voltage min
- 4,5 V
- Supply voltages max
- 37 V
You might also like
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.01
24h
Available quantity: 867
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł3.94
Delivery date unknown
No product available!
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and the current consumption up to 1.3 A. Pololu 4036
zł31.02
24h
Available quantity: 2
Available
Other products in the same category (16)
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143
zł299.62
6 weeks
No product available!
No product available!
Pololu Jrk 21v3 USB Motor Controller with Feedback (Fully Assembled)
zł483.56
24h
Available quantity: 1
Available
Pololu - 2511
zł38.63
24h
Available quantity: 2
Available
HAT module with TB6612FNG motor driver and PCA9685 PWM driver designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector. Adafruit 4280
zł133.02
24h
Available quantity: 2
Available
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
zł533.13
24h
Available quantity: 1
Available
Module of a 4-channel driver of DC motors with RP2040 microcontroller. It allows the connection of encoders and is equipped with a QW/ST connector. Pimoroni PIM636
zł146.07
24h
Available quantity: 6
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5051
zł318.35
6 weeks
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 17 A without a heat sink.
zł176.75
6 weeks
No product available!
A single-channel DC motor driver with an I2C interface. It is powered from 4.5 V to 48 V and can deliver up to 2.2 A of current. A board with soldered connectors. Pololu 5060
zł83.92
6 weeks
No product available!
Pololu TReX Dual Motor Controller DMC01
zł1,124.93
24h
Available quantity: 1
Available
Regulator for DC brush motors, 10A, built-in BEC 1A, RoHS
zł63.22
24h
Available quantity: 2
Available
Powerful DC motor driver. It allows you to control a motor with a power supply voltage in the range of 6 ... 28 V, the motor can draw current of 100 A (using a heat sink). For the control PWM modeling (eg from RC receivers) is used in robotics, small electric vehicles or wherever there is a need to control a DC motor. Digilent 410-334-1
zł467.81
4 weeks
No product available!
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
zł117.62
24h
Available quantity: 1
Available
Pololu G2 24v19 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 40V. Current efficiency of the module: 19A. The module has protection against back voltage and overvoltage. Pololu 1367
zł3,573.43
6 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5059
zł646.08
6 weeks
No product available!
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and current consumption up to 1.1 A. Pololu 4037