

Module with DC motor driver DRV8874. It allows you to control the movement of a DC motor with a voltage from 4.5 to 37 V and a current of up to 2.1 A (continuous current). The interface requires two control lines: PWM and GPIO in PH/EH mode or two PWM signals in IN/IN mode. The use of one PWM signal allows you to limit the number of inputs needed for bidirectional motor movement, but such a solution does not support the braking function. The controller has built-in protection against reverse polarity, over voltage, overload and overheating, and has an integrated current sensor and active current regulation. The logical part can be supplied with the voltage from 1.8 to 5.5 V, thanks to which the module can work with voltages of 3.3 V and 5 V.
Pinout description
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and the current consumption up to 1.3 A. Pololu 4036
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 Voperating range and are efficient enough to deliver a continuous 14 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5048
No product available!
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468
Pololu Low-Voltage Dual Serial Motor Controller
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and the current consumption up to 1.3 A. Pololu 4036
DC motor driver that allows you to control the movement of three drives using the I2C interface. Connectors for self-assembly. Pololu 5034
Pololu G2 24v19 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 40V. Current efficiency of the module: 19A. The module has protection against back voltage and overvoltage. Pololu 1367
No product available!
Pololu Simple High-Power Motor Controller 18v15
No product available!
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Pololu 2762
ESC RC controller module with FlySky receiver designed for two brush motors with a supply voltage from 2.5 to 5 V and a current consumption of 2 A
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5076
Dual VNH2SP30 Motor Driver Carrier MD03A
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1365
No product available!
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5077
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
3-channel brush motor controller module with PWM signal mixing function. It allows you to control three DC motors with a current consumption of up to 3 A per channel
No product available!
Module with DC motor driver DRV8874. It can work with motors supplied with the voltage from 4.5 to 37 V and current consumption up to 2.1 A. Pololu 4035