Two-channel driver module dedicated to DC brushed motors. It has a current capacity of up to 5 A per channel and can work with LiPo 2S and 3S packets with a rated voltage from 7.4 to 11.1 V. It requires a PWM control signal and allows you to control the motor movement in two directions. Widely used in modeling, incl. as a driver for engines of car models.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Adafruit 2348
The RoboClaw motor controller can control a pair of brushed DC motors using USB serial, TTL serial, RC or analog inputs. Integrated dual quadrature decoders make it easy to create a closed-loop speed control system. This version can supply a continuous 7.5 A per channel (15 A peak). Pololu 3284
Powerful DC motor driver. It allows you to control a motor with a power supply voltage in the range of 6 ... 28 V, the motor can draw current of 100 A (using a heat sink). For the control PWM modeling (eg from RC receivers) is used in robotics, small electric vehicles or wherever there is a need to control a DC motor. Digilent 410-334-1
No product available!
The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
HAT with TB6612FNG engine controller and PCA9685 PWM controller designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector characteristic of Raspberry Pi, making it compatible with all minicomputers with this connector. Waveshare Motor Driver HAT
Module with DC motor driver DRV8256P. It can work with motors supplied with the voltage from 4.5 to 48 V and the current consumption up to 1.9 A. Pololu 4039
No product available!
ESC RC controller module with FlySky receiver designed for two brush motors with a supply voltage from 2.5 to 5 V and a current consumption of 2 A
Pololu High-Power Motor Driver 36v9
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5050
No product available!
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR
HAT module with TB6612FNG motor driver and PCA9685 PWM driver designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector. Adafruit 4280
3-channel brush motor controller module with PWM signal mixing function. It allows you to control three DC motors with a current consumption of up to 3 A per channel
No product available!
DRV8801 Single Brushed DC Motor Driver Carrier
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
Pololu Jrk 21v3 USB Motor Controller with Feedback
No product available!
The core of a small robot, either as an auxiliary controller atop a Raspberry Pi base or as a complete control solution on its own. Its Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader. This version does not include any through-hole components or connectors, allowing for customized assembly or standalone use. Pololu 3118
DC motor driver with a working voltage from 5 to 30 V and a maximum continuous current of 13 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MD10C
Pololu Jrk 12v12 USB Motor Controller with Feedback
Driver module for two DC brushed motors with current efficiency up to 5 A per channel. It can work with LiPo 2S and 3S packets