Jrk G2 21v3 - DC motor driver (assembled)
ID: 572198
zł299.62
Tax included
zł243.59 tax excl.
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Jrk G2 21v3 USB Motor Controller is a single-channel DC motor driver. The voltage supplying the motors ranges from 4.5 to 28 V. The controller has one channel with a capacity of 2.6 A at constant power consumption. The control can be carried out via the USB port, TTL serial interface, I2C, RC receiver signal or via analog input. The controller enables easy implementation of a closed loop of engine speed control by connecting an analog or frequency input. It also allows configuration of engine operation parameters via a USB interface and a free application.
properties
- Operating voltage: 4.5 ... 28 V
- Continuous output current: 2.6 A
- Simple bi-directional DC motor control
- Automatic protection by reverse polarity
- Five control interfaces
- USB interface - Virtual COM port (microUSB connector)
- Serial TTL (UART) interface
- I2C interface
- Signal from RC apparatus (PWM 50 Hz, 5-10% filling)
- Analogue signal input
- Feedback
- Analog signal (0 - 5 V)
- Frequency for closed loop speed control using pulse counting (in the case of high frequency feedback) or pulse clocking (in the case of low frequency feedback)
- Configuration via USB interface
- PID coefficients (tuning parameters)
- Maximum current
- Maximum working cycle
- Maximum acceleration and delay
- Error response
- Input calibration (learning) for analog and RC control
- Dimensions: 30.5 x 25.5 x 12 mm
- Weight: 7.5 g
Included
- Driver Jrk G2 21v3 USB Motor Controller (assembled)
572198
Data sheet
- Output current
- 2,6 V
- Number of channels
- 1
- Supply voltage min
- 4,5 V
- Supply voltages max
- 28 V
You might also like
This powerful motor controller makes closed-loop speed or position (but not both!) control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), and hobby radio control (RC).
zł583.28
24h
Available quantity: 1
Available
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149
zł933.32
24h
Available quantity: 1
Available
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3142
zł292.36
24h
Available quantity: 1
Available
Other products in the same category (16)
HAT with TB6612FNG engine controller and PCA9685 PWM controller designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector characteristic of Raspberry Pi, making it compatible with all minicomputers with this connector. Waveshare Motor Driver HAT
zł74.53
24h
Available quantity: 2
Available
Dual DC motor controller designed for Arduino, which enables the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption in continuous operation of 2.6 A (5A at the top) of two DC motors. Polol 2520
zł132.04
24h
Available quantity: 1
Available
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, A+, or Pi 2 and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Pololu 2753
zł43.82
24h
Available quantity: 2
Available
Pololu Simple High-Power Motor Controller 24v23
zł979.55
6 weeks
No product available!
3-channel brush motor controller module with PWM signal mixing function. It allows you to control three DC motors with a current consumption of up to 3 A per channel
zł56.52
24h
Available quantity: 3
Available
This compact breakout board for Maxim’s MAX14870 motor driver offers a wide operating voltage range of 4.5 V to 36 V and can deliver a continuous 1.7 A (2.5 A peak) to a single brushed DC motor. It features a simple two-pin speed/direction interface and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature.
zł42.67
24h
Available quantity: 3
Available
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 Voperating range and are efficient enough to deliver a continuous 14 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
zł272.63
24h
Available quantity: 2
Available
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
zł40.02
24h
Available quantity: 1
Available
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł111.09
24h
Available quantity: 1
Available
A single-channel DC motor controller with a UART TTL interface. It is powered from 4.5 V to 48 V and can deliver up to 2.2 A of current. Board with soldered connectors. Pololu 5062
zł83.92
6 weeks
No product available!
DC motor driver module with two channels, dedicated to use in modeling. It can be controlled by an RC transmitter and uses the PPM signal. DFRobot DFR0513
zł72.10
24h
Available quantity: 2
Available
DC motor driver with an operating voltage from 6 to 60 V and a maximum continuous current of 300 A. It can communicate via USB, UART, RC or analog signal and allows for the implementation of a feedback loop. Pololu 3584
zł2,579.85
6 weeks
No product available!
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR
zł111.29
24h
Available quantity: 2
Available
Dual VNH2SP30 Motor Driver Carrier MD03A
zł1,135.51
24h
Available quantity: 1
Available
Single-channel DC motor driver with an operating voltage from 10 to 45 V and a continuous current up to 40 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDS40B
zł341.31
24h
Available quantity: 4
Available
The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
zł56.25
24h
Available quantity: 2
Available
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143