Jrk G2 24v21 - DC motor controller
ID: 571452
5906623478651
zł598.54
Tax included
zł486.62 tax excl.
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149
Description
Jrk G2 24v21 USB Motor Controller is a single-channel DC motor driver. The voltage supplying the motors is from 6.5 to 40 V (recommended maximum voltage 34 V). The control can be carried out via the USB port, TTL serial interface, I2C, RC receiver signal or via analog input. The controller enables easy implementation of a closed loop of engine speed control by connecting an analog or frequency input. It also allows configuration of engine operation parameters via a USB interface and a free application.
properties
- Operating voltage: 6.5 ... 40 V (absolute maximum, recommended maximum voltage 34 V)
- Continuous output current: 21 A
- Simple bi-directional DC motor control
- Automatic reverse polarity protection
- Five control interfaces
- USB interface - Virtual COM port (microUSB connector)
- Serial TTL (UART) interface
- I2C interface
- Signal from RC apparatus (PWM 50 Hz, 5-10% filling)
- Analogue signal input
- Feedback
- Analog signal (0 - 5 V)
- Frequency for closed loop speed control using pulse counting (in the case of high frequency feedback) or pulse clocking (in the case of low frequency feedback)
- Configuration via USB interface
- PID coefficients (tuning parameters)
- Maximum current
- Maximum working cycle
- Maximum acceleration and delay
- Error response
- Input calibration (learning) for analog and RC control
- Dimensions: 30.5 x 43 x 10.5 mm
- Weight: 10 g
Included
- Driver Jrk G2 24v21 USB Motor Controller
- 2 x 2-pin screw connector
- Simple male goldpin connector
571452
Data sheet
- Output current
- 21 A
- Number of channels
- 1
- Supply voltage min
- 6,5 V
- Supply voltages max
- 34 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This powerful motor controller makes closed-loop speed or position (but not both!) control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), and hobby radio control (RC).
zł450.07
24h
Available quantity: 1
Available
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143
zł232.62
Delivery date unknown
No product available!
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3142
zł225.57
Delivery date unknown
No product available!
Other products in the same category (16)
KAmodMPC17C724 is a module with a double MP bridge bridge type MPC17C724. The system allows you to control two DC brush motors or one bipolar stepping motor. The controller operates at a voltage range of 2.7 - 5.5 V and can work with motors with power consumption up to 0.4 A.
zł19.90
24h
Available quantity: 318
Available
The X-NUCLEO-IHM12A1 is a low voltage dual brush DC motor driver expansion board based on the STSPIN240 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys
zł56.25
24h
Available quantity: 1
Available
The high power motor driver module works on the basis of Infineon BTS7960B systems. Maximum controller current: 43 A, operating voltage range: 5.5V - 27V. The module has a heat sink and can be controlled from the Arduino, Raspberry Pi, and STM levels. IBT_2
zł39.96
4 weeks
No product available!
No product available!
Powerful DC motor driver. It allows you to control a motor with a power supply voltage in the range of 6 ... 28 V, the motor can draw current of 100 A (using a heat sink). For the control PWM modeling (eg from RC receivers) is used in robotics, small electric vehicles or wherever there is a need to control a DC motor. Digilent 410-334-1
zł467.81
3 weeks
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 Voperating range and are efficient enough to deliver a continuous 14 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
zł315.67
24h
Available quantity: 2
Available
HAT module with a driver for two DC motors designed for Raspberry Pi. Motors can be powered with the voltage from 6.5 to 30 V and draw a maximum current of up to 18 A. Pololu 3751
zł331.50
4 weeks
No product available!
This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation.
zł327.55
24h
Available quantity: 1
Available
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
zł288.26
24h
Available quantity: 1
Available
Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 30V voltage and can draw up a maximum current of 22A. Polol 2517
zł598.99
4 weeks
No product available!
Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756
zł423.01
4 weeks
No product available!
Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be powered with 6.5-30V and draw up a maximum current of 22A. Pololu 3754
zł605.05
4 weeks
No product available!
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
zł65.65
24h
Available quantity: 3
Available
The RoboClaw Solo motor controllers from Basicmicro (formerly Ion Motion Control) can control a single brushed DC motor using USB serial, TTL serial, RC, or analog inputs. An integrated quadrature decoder make it easy to create a closed-loop speed control system.
zł498.17
24h
Available quantity: 1
Available
The RoboClaw Solo motor controllers from Basicmicro (formerly Ion Motion Control) can control a single brushed DC motor using USB serial, TTL serial, RC, or analog inputs. Pololu 3291
zł718.04
4 weeks
No product available!
2x1.2A DC Motor Driver is a dual controller of DC motors with a Gravity connector, supplied with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044-A
zł40.02
24h
Available quantity: 1
Available
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149