PPM 2x3A DC Motor Driver - two-channel driver for DC motors
ID: 571609
5902186313712
zł69.46
Tax included
zł56.47 tax excl.
DC motor driver module with two channels, dedicated to use in modeling. It can be controlled by an RC transmitter and uses the PPM signal. DFRobot DFR0513
Description
DC motor driver module with two channels, dedicated to use in modeling. It can be controlled by an RC transmitter and converts the PPM signal into a signal that controls the speed and direction of the motor. There are two signal reception channels (CH1, CH2) and two output channels (M1, M2) on the board. Each input channel uses a standard 50 Hz PPM signal with a duty cycle of 5% to 10%.
The controller can be powered with the voltage from 7 to 12 V, and the continuous current of each channel is 3 A. The permissible peak current is 6 A. When the current exceeds 6 A, the controller system enters the lock state (requires re-powering) to run the driver). The module has a built-in LDO stabilizer that can provide an external 5V / 200mA power supply. Thanks to this, the remote control receiver in the model can be connected directly to the controller board without additional power supply. Full documentation and example applications are available on the product page.
Features
- 2 channels for controlling DC motors
- Controlled by PPM signal, compatible with servo control signal
- Designed for modeling
- Overload protection
- Input voltage: 7 to 12V
- Logic power supply: 5V (compatible with 3.3V controller)
- Main chip: STM8S105
- Driver chip: TLE5205
- Control signal: 1000 to 2000 us
- Maximum continuous current per channel: 3 A
- Maximum instantaneous current per channel: 6 A
- Dimensions: 90 x 30 mm
- Weight: 35 g
571609
Data sheet
- Output current
- 3A
- Number of channels
- 2
- Supply voltage min
- 7
- Supply voltages max
- 12 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Motor with 25 mm diameter and 46 mm length, 12 V operating voltage, 0,15 A to 5,6 A power consumption, 10200 RPM speed, 0,4 maximum torque and 48 CPR encoder. Pololu 4840
zł240.48
Delivery date unknown
No product available!
Motor with 25 mm diameter and 71 mm length, 172:1 metal gear, 12 V operating voltage, 0,1 A to 1,1 A power consumption, 31 RPM speed, 13 maximum torque and 48 CPR encoder. Pololu 4888
zł350.28
Delivery date unknown
No product available!
Motor with 25 mm diameter and 56 mm length, 172:1 metal gear, 12 V operating voltage, 0,1 A to 1,1 A power consumption, 31 RPM speed and 13 maximum torque. Pololu 3256
zł188.56
Delivery date unknown
No product available!
Other products in the same category (16)
Motoron M3S256 Triple Motor Controller Shield - 3-channel DC motor driver for Arduino (for assembly)
DC motor driver that allows you to control the movement of three drives using the I2C interface. Plate with connectors for assembly. Pololu 5031
zł202.77
4 weeks
No product available!
Module with a DC motor driver based on the MC33886 chip. It allows you to control the movement of drives with a working voltage from 5 to 28 V and a current of up to 5 A
zł41.43
4 weeks
No product available!
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł102.94
24h
Available quantity: 3
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5042
zł628.89
4 weeks
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
4 weeks
No product available!
2x1.2A DC Motor Driver is a dual controller of DC motors powered with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044
zł20.82
24h
Available quantity: 6
Available
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468
zł76.48
24h
Available quantity: 2
Available
TB6612FNG Dual Motor Driver Carrier
zł20.90
24h
Available quantity: 25
Available
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
zł56.04
24h
Available quantity: 1
Available
HAT with TB6612FNG engine controller and PCA9685 PWM controller designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector characteristic of Raspberry Pi, making it compatible with all minicomputers with this connector. Waveshare Motor Driver HAT
zł67.00
24h
Available quantity: 2
Available
Pololu High-Power Motor Driver 24v20
zł221.29
24h
Available quantity: 1
Available
Available
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with soldered connectors. Pololu 5076
zł68.14
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5044
zł574.14
4 weeks
No product available!
No product available!
Two-channel driver of direct current (DC) motors with an operating voltage from 5 to 30 V and a maximum continuous current of 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD10A
zł93.28
24h
Available quantity: 11
Available
DC motor driver module with two channels, dedicated to use in modeling. It can be controlled by an RC transmitter and uses the PPM signal. DFRobot DFR0513