Jrk G2 24v13 - DC motor controller
ID: 571450
5906623478637
zł460.81
Tax included
zł374.64 tax excl.
DC motor driver with voltage 6.5 ... 40V and maximum continuous current 13A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3147
Description
Jrk G2 24v13 USB Motor Controller is a single-channel DC motor driver. The voltage supplying the motors is from 6.5 to 40 V (40 V maximum recommended). The control can be carried out via the USB port, TTL serial interface, I2C, RC receiver signal or via analog input. The controller enables easy implementation of a closed loop of engine speed control by connecting an analog or frequency input. It also allows configuration of engine operation parameters via a USB interface and a free application.
properties
- Operating voltage: 6.5 ... 40 V (absolute maximum, recommended maximum voltage 40 V)
- Continuous output current: 13 A
- Simple bi-directional DC motor control
- Automatic reverse polarity protection
- Five control interfaces
- USB interface - Virtual COM port (microUSB connector)
- Serial TTL (UART) interface
- I2C interface
- Signal from RC apparatus (PWM 50 Hz, 5-10% filling)
- Analogue signal input
- Feedback
- Analog signal (0 - 5 V)
- Frequency for closed loop speed control using pulse counting (in the case of high frequency feedback) or pulse clocking (in the case of low frequency feedback)
- Configuration via USB interface
- PID coefficients (tuning parameters)
- Maximum current
- Maximum working cycle
- Maximum acceleration and delay
- Error response
- Input calibration (learning) for analog and RC control
- Dimensions: 30.5 x 35.5 x 10.5 mm
- Weight: 6.5 g
Included
- Driver Jrk G2 24v13 USB Motor Controller
- 2 x 2-pin screw connector
- Simple male goldpin connector
571450
Data sheet
- Output current
- 13 A
- Number of channels
- 1
- Supply voltage min
- 6,5 V
- Supply voltages max
- 40 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This powerful motor controller makes closed-loop speed or position (but not both!) control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), and hobby radio control (RC).
zł450.07
24h
Available quantity: 1
Available
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149
zł598.54
Delivery date unknown
No product available!
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3143
zł232.62
Delivery date unknown
No product available!
DC motor driver with voltage 4.5..28V and maximum continuous current of 2.6A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3142
zł225.57
Delivery date unknown
No product available!
Other products in the same category (16)
DRV8835 Dual Motor Driver Carrier
zł23.90
24h
Available quantity: 8
Available
The board based on the L298 Dual Full-Bridge Motor Driver; can provide up to 4 Amps of current to the motors (2 Amps per motor). ROB-09571
zł167.12
24h
Available quantity: 3
Available
No product available!
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS
zł9.45
24h
Available quantity: 8
Available
Dual H-Bridge motor driver board, 2A, 36V max, L298N, RoHS
zł12.60
24h
Available quantity: 7
Available
(DRI0009) 2A Motor Shield For Arduino
zł61.27
24h
Available quantity: 3
Available
DRV8801 Single Brushed DC Motor Driver Carrier
zł60.64
24h
Available quantity: 2
Available
A4990 Dual Motor Driver Carrier
zł44.97
24h
Available quantity: 1
Available
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł102.94
24h
Available quantity: 3
Available
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. Pololu 2507
zł294.77
4 weeks
No product available!
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, A+, or Pi 2 and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Pololu 2753
zł56.70
24h
Available quantity: 2
Available
Pololu - 2511
zł41.29
24h
Available quantity: 1
Available
Available
Tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor. Operating voltage range from 0 V to 11 V, built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature. Pololu 2990
zł17.65
24h
Available quantity: 8
Available
This compact breakout board is for ROHM’s BD65496MUV motor driver, which offers an operating voltage range of 2 V to 16 V and can deliver a continuous 1.2 A to a single brushed DC motor. Pololu 2960
zł71.08
24h
Available quantity: 2
Available
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
zł113.25
24h
Available quantity: 3
Available
DC motor driver with voltage 6.5 ... 40V and maximum continuous current 13A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3147