Pololu G2 18v15 HP - DC Motor Driver (assembled)
ID: 573139
5906623479627
zł532.48
Tax included
zł432.91 tax excl.
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
Description
Pololu G2 18v15 High Power is a DC motor controller in the form of a H bridge, built based on N-MOSFET transistors. The module can be supplied with voltage from the range of 6.5 ... 30 V. The maximum continuous current supplying the DC motor is 15 A. The controller does not require additional cooling. The controller module has a current measurement circuit taken by the motor which allows setting the current limit. The motor is controlled by means of RC signal, through the I2C interface, UART interface, USB interface or analog interface. The logic part of the controller works with a 3.3V voltage. The software update of the controller and the configuration takes place via the USB interface. The module has soldered connectors.
Attention!
The set does not include a USB cable . It should be purchased separately.
properties
- Supply voltage: 6.5 V to 30 V (absolute maximum)
- Continuous output current: 15 A
- Adjustable maximum acceleration and delay
- Adjustable initial and maximum speed
- Possibility of braking or running
- Input calibration for analog and RC signals
- Adjustable threshold and reaction to excessive temperature
- Adjustable PWM frequency from 1.13 kHz to 22.5 kHz
- Error LED connected to the digital ERR output
- Protection against back voltage
- Short-circuit protection
- Current measurement circuit for the motor
- The controller's logic is powered by 3.3V
- Dimensions: 53.5 x 28 x 12.7 mm
- Weight: 12.5 g
573139
Data sheet
- Output current
- 15 A
- Number of channels
- 1
- Supply voltage min
- 6,5 V
- Supply voltages max
- 30 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł181.07
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 17 A without a heat sink.
zł184.19
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
Delivery date unknown
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 40 V voltage range and is efficient enough to deliver a continuous 21 A without a heat sink.
zł202.75
Delivery date unknown
No product available!
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1363
zł551.54
24h
Available quantity: 1
Available
Other products in the same category (16)
Pololu - 2511
zł41.29
24h
Available quantity: 1
Available
Available
Tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor. Operating voltage range from 0 V to 11 V, built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature. Pololu 2990
zł17.32
24h
Available quantity: 8
Available
This compact breakout board is for ROHM’s BD65496MUV motor driver, which offers an operating voltage range of 2 V to 16 V and can deliver a continuous 1.2 A to a single brushed DC motor. Pololu 2960
zł71.08
24h
Available quantity: 2
Available
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
zł113.25
24h
Available quantity: 3
Available
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł181.07
4 weeks
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 17 A without a heat sink.
zł184.19
4 weeks
No product available!
Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader, and the board includes dual motor drivers that can deliver 1.7 A per channel to two brushed DC motors. Pololu 3119
zł245.34
24h
Available quantity: 1
Available
The core of a small robot, either as an auxiliary controller atop a Raspberry Pi base or as a complete control solution on its own. Its Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader. This version does not include any through-hole components or connectors, allowing for customized assembly or standalone use. Pololu 3118
zł197.60
24h
Available quantity: 2
Available
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
zł286.68
4 weeks
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 40 V voltage range and is efficient enough to deliver a continuous 21 A without a heat sink.
zł202.75
4 weeks
No product available!
This add-on board enables a Raspberry Pi B+, Pi A+, Pi 2 or Pi 3 to drive a pair of brushed DC motors. Its dual MC33926 motor drivers operate from 5 V to 28 V and can deliver a continuous 3 A (5 A peak) per motor. The default pin mappings make it easy to get started using our provided software, but the board also exposes most of the driver chips’ I/O pins for more specialized applications.
zł199.00
4 weeks
No product available!
This compact breakout board for Maxim’s MAX14870 motor driver offers a wide operating voltage range of 4.5 V to 36 V and can deliver a continuous 1.7 A (2.5 A peak) to a single brushed DC motor. It features a simple two-pin speed/direction interface and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature.
zł42.46
24h
Available quantity: 2
Available
Two-channel DC motor driver based on the HR9933 circuit. It allows you to control the movement of drives with a supply voltage of up to 10 V and power consumption up to 1.5 A. DFRobot DRI0040
zł21.46
24h
Available quantity: 4
Available
Single-channel DC motor driver that can control the movement of the drive with a supply voltage of up to 36 V and a current consumption of up to 15 A. Controlled by a PWM signal. DFRobot DRI0042
zł129.97
24h
Available quantity: 2
Available
Ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. DRI0041
zł86.65
24h
Available quantity: 1
Available
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362