![TB67H420FTG Dual / Single Motor Driver Carrier - DC motor driver TB67H420FTG Dual / Single Motor Driver Carrier - DC motor driver](https://kamami.pl/32005-large_default/tb67h420ftg-dual-single-motor-driver-carrier-dc-motor-driver.jpg)
![TB67H420FTG Dual / Single Motor Driver Carrier - DC motor driver TB67H420FTG Dual / Single Motor Driver Carrier - DC motor driver](https://kamami.pl/32005-large_default/tb67h420ftg-dual-single-motor-driver-carrier-dc-motor-driver.jpg)
zł47.19 tax excl.
The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
TB67H420FTG Dual / Single Motor Driver Carrier is a universal DC motor controller enabling control of independently two DC motors or one motor with an increased current load. The controller can be used for motors supplied with voltage in the range of 10-47 V and continuous current consumption of 1.7 A (4.5 A at peak) for each channel in dual or 3.4 A mode (9 A at peak) in one channel mode. The controller is protected by overheating and overcurrent and has reverse voltage protection.
Attention!
The capacitors used in the system have a nominal voltage of 50 V. Special care should be taken when using motors in excess of the nominal voltage, because the capacitors may be damaged.
The maximum current consumed by the motors can be limited by the user by the possibility of using a resistor between the controller VREFA and VREFB leads. The motor can be controlled by a three-pin interface (two pins of the direction and PWM signal) or by controlling two PWM signals given on the direction pins.
Data sheet
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink.
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 40 V voltage range and is efficient enough to deliver a continuous 21 A without a heat sink.
Motor with 20 mm diameter and 46 mm length, 250:1 metal gear, 12 V operating voltage, 0.08 A to 1.6 A power consumption, 55 RPM speed and 14 kg*cm maximum torque. Pololu 3494
RoboClaw 2x160A Motor Controller is a two-channel DC motor driver, operating voltage: 10.5..60V, maximum continuous current: 120A, easy implementation of feedback loops with PID controller, safety systems. Pololu 3582
No product available!
Two-channel driver of direct current (DC) motors with an operating voltage from 6 to 30 V and a maximum continuous current of 20 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD20A
Compact stepper motor controller with the TMC2208 system with operating voltage from 4 to 35 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via the STEP/DIR interface and is an ideal solution for 3D printers and similar applications
Module with bipolar stepper motor driver TC78H670FTG. It allows you to control the motor with an accuracy of 1/128 of a step with a voltage from 3.6 to 16 V and a current of up to 2 A. SparkFun ROB-16836
Pololu Simple High-Power Motor Controller 18v25
No product available!
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5081
Pololu High-Power Motor Driver 36v15
Stepper motor driver that can operate with a voltage in the range from 24 to 110 VDC or from 18 to 80 VAC and a maximum current of 7.2 A. It allows for microstep configuration in the range from 2 to 256. DM860H
The expansion module is designed to work with the micro:bit educational board. It can control 3 servos and 2 DC motors. Waveshare Motor Driver for micro:bit
DC motor driver with voltage 6.5 ... 40V and maximum continuous current 13A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3147
Single-channel DC motor controller enabling motor control with voltage in the range of 7-30V and current up to 10A. The set has a potentiometer and a direction switch. Cytron MD10_POT
Module with TMC2208 stepper motor driver. It enables control with a supply voltage ranging from 5.5 to 34 V and a current of up to 1,2 A
No product available!
Stepper motor driver that can work with a voltage in the range from 20 to 50 V and a maximum current of 4.2 A. It allows you to configure the microstep in the range from 2 to 128. DM542
A two-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with soldered connectors. Pololu 5078
A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2981
The controller enables to supply the motors with voltage in the range of 10-47V and power consumption in continuous operation of 1.7A (4.5A peak) for each channel in dual or 3.4A mode (9A peak) in single channel mode. Pololu 2999