zł64.19 tax excl.
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5081
A DC motor controller that allows the movement of two drives to be controlled via a UART TTL interface. It can operate with motors with supply voltages from 1.8 to 22 V and has a capacity of up to 1.6 A per motor (continuous operation). The controller has built-in protection in case of loss of communication with the main controller and a configurable response if an error occurs. The user can set the maximum acceleration and initial speed of the motor Using a single UART bus, it can control several modules. A user manual and a library with example programmes are available on the manufacturer's website.

Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors. Pololu 5080
A two-channel DC motor controller with a I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5079
A two-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with soldered connectors. Pololu 5078
Two-channel driver for DC motors with an operating voltage from 7 to 35 V and a continuous current up to 10 A. It can be controlled by an analog signal, PWM, UART, RC or by means of built-in buttons. Cytron MDDS10
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, A+, or Pi 2 and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Pololu 2753
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5040
No product available!
Two-channel driver of direct current (DC) motors with an operating voltage from 6 to 30 V and a maximum continuous current of 20 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD20A
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14451
Module with 2-channel DC motor driver DRV8833 designed to work with the Raspberry Pi Pico. It can work with a voltage from 2.7 to 10.8 V and a current of up to 1.2 A. Pimoroni PIM617
Module with a 2-channel DC motor driver TB6612FNG designed to work with micro: bit. It can also control 3 servos. SB Components 14897
Pololu High-Power Motor Driver 36v15
Module with two DRV8830 DC motor drivers. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020010
3-channel brush motor controller module with PWM signal mixing function. It allows you to control three DC motors with a current consumption of up to 3 A per channel
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5057
No product available!
Miniature ESC type controller for a DC motor with an input from 3.7 V to 5 V. Offers an additional output current of up to 1.5 A and allows you to control the motor in a channel mixing device
Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Raspberry Pi. The motors can be supplied with 6.5-36V voltage and can draw a maximum current of 18A. Pololu 3756
No product available!
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
Pololu Simple High-Power Motor Controller 24v12 (Fully Assembled)
A two-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.6 A per motor. Board with connectors for assembly. Pololu 5081