Qwiic Triple Axis Accelerometer Breakout - a module with a 3-axis MMA8452Q accelerometer
ID: 570703
5906623419944
zł73.01
Tax included
zł59.36 tax excl.
Module with the 3-axis MMA8452Q accelerometer. The system has a user selectable measurement scale of ±2g/±4g/±8g. There are two Qwiic connectors on the board and holes with 2.54 mm raster. SparkFun SEN-14587
Description
Module with the 3-axis MMA8452Q accelerometer. The system has a user selectable measurement scale of ±2g/±4g/±8g with high-pass filtered data as well as unfiltered data available in real time. The device can be configured to generate inertial interrupt signals, allowing you to monitor events and remain in a low-power mode during idle periods. The MMA8452Q can send data with 12-bit resolution and a frequency of up to 800 Hz. There are two Qwiic connectors on the board and holes with 2.54 mm raster. The product page includes the user manual and the Arduino library.
Features
- Range: ±2g/±4g/±8g selectable dynamically
- Data transmission frequency (ODR) between 1.56 Hz and 800 Hz
- 12-bit and 8-bit digital output
- Digital I2C interface (works up to 2.25 MHz with 4.7 kΩ pull-up)
- I2C address: 0x1D (default), 0x1C
- Two programmable interrupt pins for six interrupt sources
- Three built-in motion detection channels
- Orientation detection with set hysteresis
- Real-time high-pass filter data
- 2 x Qwiic connector
- Supply voltage from 1.95 V to 3.6 V
- Interface voltage 1.6 V to 3.6 V
- Current consumption: 6 μA - 165 μA
570703
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
zł1.50
24h
Available quantity: 14129
Available
Set of 40 pieces of male-female connection cables, in various colors, 17 cm long. CAB_M-F (Rainbow-40-17)
zł5.68
24h
Available quantity: 694
Available
No product available!
Flexible 4-core cable, 100 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17259
zł12.50
24h
Available quantity: 39
Available
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
zł12.90
24h
Available quantity: 10
Available
Other products in the same category (16)
Module of the 3-axis LIS2DH, I2C accelerometer. DFRobot SEN0224
zł20.75
24h
Available quantity: 2
Available
Module with the 3-axis MMA8452Q accelerometer. The system has a user selectable measurement scale of ±2g/±4g/±8g. There are two Qwiic connectors on the board and holes with 2.54 mm raster. SparkFun SEN-14587
zł73.01
24h
Available quantity: 1
Available
KAmodMMA8451Q is a module with the MMA8451Q three-axis accelerometer from NXP. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMMA8451Q
zł24.90
24h
Available quantity: 233
Available
KAmodMMA8653FC is a module with NXP's MMA8653FC three-axis accelerometer. The sensor allows the measurement of acceleration in the range of ± 2g / ± 4g / ± 8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor takes place via the I2C interface
zł26.90
24h
Available quantity: 459
Available
Module with a 3-axis ADXL343 accelerometer with a configurable measuring range of ±2g/±4g/±8g/±16g. Equipped with a STEMMA QT connector, it communicates via the I2C or SPI interface. Adafruit 4097
zł28.83
24h
Available quantity: 1
Available
Module with 3-axis digital accelerator ADXL345, SPI and I2C communication.
zł13.70
24h
Available quantity: 8
Available
KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes.
zł19.90
24h
Available quantity: 462
Available
Module with the 3-axis ADXL313 accelerometer with measuring ranges of ± 0.5 g, ± 1 g, ± 2 g or ± 4 g. The system is characterized by high 13-bit resolution and low power consumption. SparkFun SEN-17241
zł84.69
24h
Available quantity: 1
Available
A module with a 3-axis accelerometer that allows you to measure acceleration in the range of ± 16g with a resolution of 13 bits. GY-291 ADXL345
zł14.30
24h
Available quantity: 29
Available
Module with the LIS3DHTR 3-axis accelerometer. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 114020121
zł24.06
24h
Available quantity: 1
Available
Module with a 3-axis BMA400 accelerometer with a measuring range up to ± 16g. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020582
zł43.53
24h
Available quantity: 3
Available
Module with BMA456 pedometer, which combines an acceleration sensor and built-in step counting algorithms. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020583
zł38.19
24h
Available quantity: 2
Available
KAmodMC3635 is a module with the MC3635 three-axis accelerometer from mCube. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g/±12g/±16g, the measurement frequency is from 14 to 1300 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMC3635
zł14.90
24h
Available quantity: 452
Available
Module with a 3-axis H3LIS331 accelerometer with a wide measurement range up to ± 400g. It communicates via the I2C or SPI interface. SparkFun SEN-14480
zł90.64
24h
Available quantity: 2
Available
Module with a 3-axis ADXL345 digital accelerometer with a configurable measuring range of ± 2/4/8/16 g. It is supplied with the voltage from 2 to 3.6 V and communicates via the I2C or SPI interface. DFRobot SEN0032
zł28.55
24h
Available quantity: 1
Available
Module with a 3-axis BMA220 digital accelerometer with a configurable measuring range of ± 2/4/8/16 g. It is supplied with the voltage from 2 to 3.6 V and communicates via the I2C or SPI interface. DFRobot SEN0168
zł20.22
24h
Available quantity: 2
Available
Module with the 3-axis MMA8452Q accelerometer. The system has a user selectable measurement scale of ±2g/±4g/±8g. There are two Qwiic connectors on the board and holes with 2.54 mm raster. SparkFun SEN-14587