Products
Categories
- Main categories
-
- 3D PRINTING
- ACADEMIC OFFER
- ARDUINO
- AUTOMATION
- BOOKS
- DIY KITS
- AVT kits
- Audio
- Car
- Chargers
- Clocks, timers and schedule switches
- Communication
- Converters
- Development kits and modules
- Displays
- Electronic games
- Generators
- Hobbies and fun
- House
- Interfaces
- Light effects
- meters
- PC
- Power Supplies
- Pre-programmed circuits
- Printed circuit boards (PCB)
- Programmers
- Regulators, controllers
- Remote control
- Starter sets Ośla Łączka
- Starting sets for beginners
- Workshop tools
- Audio
- Other sets
- TOP-Q kits
- Totem
- UGears
- Velleman
- AVT kits
- EBOOKS
- ELECTRONICS
- Cables
- Cameras and accessories
- Communication
- Conductive materials
- Connectors
- ARK connectors (Terminal Block)
- Coaxial connectors (RF)
- Connectors
- Crocodile clip
- D-Sub drawer connectors
- DC power connectors
- FFC/FPC ZIF connectors
- Goldpin connectors
- IDC connectors
- JACK connectors
- JST connectors
- Jumpers
- Memory cards slots
- Other connectors
- Pogo pin
- RJ45 sockets
- Slip ring connector
- Supports
- Szybkozłącza
- USB connectors
- Cooling
- Displays
- Electronic modules
- A/D and D/A converters
- Audio
- Barcode readers
- CAN converters
- Converters USB - UART / RS232
- Data logger
- DDS/PLL generators
- Digital potentiometers
- Encoders
- Expanders of the I/O
- Fingerprint readers
- HMI modules
- Image and video
- JTAG accessories
- Keyboards, buttons
- LED drivers
- Memory card readers
- Memory modules
- Modules with power outputs
- Motor controllers
- Power modules
- RS485 converters
- RTC modules
- Servo Controllers
- TSOP infrared receivers
- USB Converters - I2C / 1-Wire / SPI
- Voltage converters
- Gadgets
- GPS
- Intelligent clothes
- LED - diodes, displays, stripes
- Luminous wires and accessories
- Memory cards and other data storages
- Passive elements
- PC accessories
- Printers
- Prototype boards
- Semiconductors
- A/C converters (ADC)
- Analog systems
- Audio systems
- Bridge rectifiers
- Button
- D/A Converters (DAC)
- DDS synthesizers
- Digital circuits
- Diodes
- Drivers of motors
- DSP microprocessors
- Energy counters
- Energy harvesting
- ESD security
- IGBT drivers and bridges
- Interface systems
- LED drivers
- Logic converters
- Memory
- Microcontrollers
- Optotriacs and optocouplers
- Other
- PLL generators
- Power systems
- Programmable systems
- Resetting systems
- RF systems
- RTC systems
- Sensors
- SoC systems
- Timery
- Touch sensors
- Transistors
- Sensors
- Accelerometers
- Air humidity sensors
- Air quality sensors
- Current sensors
- Distance sensors
- Flow sensors
- Gas sensors
- Gyroscopes
- Hall sensors
- Humidity sensors
- Infrared sensors
- Light and color sensors
- Liquid level sensors
- Magnetic sensors (compasses)
- Medical sensors
- Motion sensors
- PH sensors
- Position sensors
- Pressure sensors
- Pressure sensors
- Reflection sensors
- Sensors 6DOF/9DOF/10DOF
- Sensors of liquid quality
- Temperature sensors
- Vibration sensors
- Sound transducers
- Switches and buttons
- Cables
- INTERNET OF THINGS (IoT)
- MECHANICS
- POWER
- R/C MODELLING
- RASPBERRY PI
- Accessories for Raspberry Pi
- Audio video cables for Raspberry Pi
- Case Raspberry Pi
- Cooling for Raspberry Pi
- Displays for Raspberry Pi
- Extension modules for Raspberry Pi
- Memory cards for Raspberry Pi
- Power for Raspberry Pi
- Raspberry Pi 3 model A+
- Raspberry Pi 3 model B
- Raspberry Pi 3 model B+
- Raspberry Pi 4 model B
- Raspberry Pi 400
- Raspberry Pi 5
- Raspberry Pi cameras
- Raspberry Pi Compute Module
- Raspberry Pi model A/ B+/2
- Raspberry Pi Pico
- Raspberry Pi prototyping
- Raspberry Pi Zero
- Raspberry Pi Zero 2 W
- RETIRED PRODUCTS
- ROBOTICS
- SALE
- SOFTWARE
- STARTER KITS, PROGRAMMERS, MODULES
- Alchitry FPGA
- Altera FPGA
- Analog electronics
- Atmel SAM
- Atmel Xplain
- AVR
- Banana Pi
- BeagleBone
- chipKIT
- Coral
- CPLD Xilinx
- Cubieboard
- DFRobot FireBeetle
- Feather
- Freedom (Kinetis)
- FriendlyELEC
- HummingBoard
- Intelligent clothes
- Kit with a book
- LattePanda
- LPC (NXP)
- M5Stack
- Micro:bit
- Nvidia Jetson
- Odroid
- ODYSSEY
- Orange Pi
- Other development kits
- Peripheral modules
- PIC
- Raisonance
- Raspberry Pi RP2040
- RFID
- RISC-V
- SBC Embest
- SBC MYIR
- SBC others
- SBC UDOO
- Segger programmers
- SoMLabs
- Sparkfun MicroMod
- STM32
- STM32 Discovery
- STM32 MP1
- STM32 Nucleo boards
- STM8
- Teensy
- Universal programmers
- WRTNode
- Xilinx FPGAs
- WORKSHOP
- Adhesives and gluers
- Anti-static mats (ESD)
- Chemistry
- CNC milling machines
- Crimping tools
- Dispensing needles
- Drills
- Files
- Generators
- Handles, magnifiers
- Heat-shrink tubing
- Insulation strippers
- Keys
- Knives and scissors
- Laboratory power supplies
- Laminates
- Measuring devices
- Mikroskopy
- Mini drills and grindrers
- Organizers
- Oscilloscopes and accessories
- Pliers and pincers
- Power tools
- Riveting tools and rivets
- Screwdrivers
- SMD Accessories
- Soldering
- Tapes (aluminum, kapton, copper, insulating)
- Tweezers
- Ultrasonic cleaners
- Vices
- 3D PRINTING
New products
New products
zł47.84 tax excl.
DFRobot DFR0316
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
INTRODUCTION:
The module integrates MCP3432 A/D converter chip. The module can provide analog input function for Raspberry Pi and provide high accuracy analog input for Arduino.
MCP3424 is one of the low noise and high accuracy 18-Bit delta-sigma analog-to-digital (ΔΣ A/D) converter family members of the MCP342X series. Its characteristic is:
Self calibration of internal offset and gain per each conversion.
User can select the PGA gain before the analog-to-digital conversion takes place. This allows the device to convert a very weak input signal with high resolution.
The device have two conversion modes:
- (a)One-Shot mode: the device performs a single conversion and enters a low current standby mode automatically until it receives another conversion command.
- (b)Continuous mode: the conversion takes place continuously at the set conversion speed.
APPLICATIONS:
- Temperature Sensing with RTD, Thermistor, and Thermocouple
- Bridge Sensing for Pressure, Strain, and Force
- Weigh Scales
- Battery Fuel Gauges
SPECIFICATION:
- Operating Voltage: 2.7 - 5.5V
- Standy Current: 300nA (5V)
- Operating Temperature: -40°C ~ +125°C
- On-Board Voltage Reference: 2.048V ± 0.05%, Drift 15 PPM /°C
- On-Board Programmable Gain Amplifier (PGA): x1,x2,x4,x8
- Differential Input Full Scale Range: -2.048V / PGA ~ 2.048V / PGA (e.g., PGA=4, Range is -0.512 ~ 0.512V)
- Programmable Resolution: 12, 14, 16, 18bits
- Programmable Data Rate: 240, 60, 15, 3.75 SPS
- Gain Error: 0.05% (PGA = 1, 18bits)
- Offset Error: 15uV (PGA = 1, 18bits)
- Input Interface: 4 differential channels, PIN header of 2.54mm spacing
- Output Interface: I2C, PIN header of 2.54mm spacing
- Size: 27x16mm(1.06x0.63")
SHIPPING LIST:
- MCP3424 18-Bit ADC-4 Channel with Programmable Gain Amplifier x1
You might also like
ADC and DAC converter module based on the PCF8591 system with I2C and the possibility of cascading other I2C modules. Waveshare PCF8591 AD DA Board
No product available!
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
Other products in the same category (16)
A module with a 24-bit ADC converter HX711, which allows you to read data from strain gauges and scales. It communicates via the serial interface. SparkFun SEN-13879
12-bit DAC converter module designed to work with the M5Stack sets. It enables the conversion of digital signals into an analog signal. M5Stack DAC Unit
Extension module with ADC AD7616 converter dedicated to FPGA boards. It offers 32 channels with a resolution of 16 bits and an FMC LPC connector. Numato Lab NLFMCADC002
No product available!
8-channel module with current analog outputs ranging from 0 to 20 mA. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in a housing that can be mounted on an industrial rail. Waveshare Modbus RTU Analog Output 8CH
No product available!
Module with 4-channel ADC ADS1015 converter. The system enables analog voltage conversion for both single signals (11-bit resolution) and differential signals (12-bit resolution). I2C communication. SparkFun DEV-15334
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
Dual-channel DAC converter compatible with the SYZYGY standard. The module can simultaneously generate two 5V signals with 14-bit resolution and sampling frequency up to 100MS/s. The module is compatible with Eclypse Z7 and Genesys ZU evaluation kits. Digilent Zmod AWG 1411 410-397
No product available!
Module with 8 inputs for data acquisition from 0-24 mA analog current inputs. It communicates via Ethernet interface and supports Modbus TCP protocol. The board is enclosed in an industrial enclosure. GM4008
DAC converter module with current output in the range of 0 to 25 mA. It is powered by 18 V to 24 V and communicates via I2C interface (Gravity connector). It is used as a controller in industrial applications. DFRobot DFR0972
3-channel voltage and current monitoring module designed to work with the Raspberry Pi. It can measure voltage ranging from 0 to 26 V and voltage ± 3.2 A. SB Components 20805
Gravity module designed based on the GP8413 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.2%. It allows you to generate analog signals with a voltage range from 0 to 10 V or 0 to 5 V. DFRobot DFR1073
Gravity module designed based on the GP8503 system. It is a two-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with 12-bit resolution and 0.1% accuracy. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1034
A module with a 24-bit ADC converter HX711, which enables reading data from strain gauges and scales. The board is equipped with a Grove connector and communicates via a serial interface. Seeed Studio 101020712
Module with 16-bit AD5693R DAC converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 5811
Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552
Gravity module designed based on the GP8512 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1035